- 您现在的位置：买卖IC网 > PDF目录16806 > ADM1166ACPZ (Analog Devices Inc)IC SEQUENCER/SUPERVISOR 40LFCSP PDF资料下载
参数资料
| 型号： | ADM1166ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 21/32页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCER/SUPERVISOR 40LFCSP |
| 标准包装： | 1 |
| 系列： | Super Sequencer® |
| 应用： | 电源监控器，序列发生器 |
| 输入电压： | 3 V ~ 14.4 V |
| 电源电压： | 3 V ~ 14.4 V |
| 电流 - 电源： | 4.2mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-WQ（6x6） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
ADM1166
VOLTAGE READBACK
The ADM1166 has an on-board, 12-bit accurate ADC for
voltage readback over the SMBus. The ADC has a 12-channel
analog mux on the front end. The 12 channels consist of the
Table 9. ADC Input Voltage Ranges
Attenuation
SFD Input Range (V) Factor
ADC Input Voltage
Range (V)
The upper limit is the absolute maximum allowed voltage on the VPx and
10 SFD inputs (VH, VPx, and VXx) and two auxiliary (single-
ended) ADC inputs (AUX1 and AUX2). Any or all of these inputs
can be selected to be read, in turn, by the ADC. The circuit
controlling this operation is called the round-robin circuit.
This circuit can be selected to run through its loop of conversions
once or continuously. Averaging is also provided for each channel.
In this case, the round-robin circuit runs through its loop of
conversions 16 times before returning a result for each channel. At
the end of this cycle, the results are written to the output registers.
The ADC samples single-sided inputs with respect to the AGND
pin. A 0 V input gives out Code 0, and an input equal to the
voltage on REFIN gives out full code (4095 decimal).
The inputs to the ADC come directly from the VXx pins and
from the back of the input attenuators on the VPx and VH pins,
0.573 to 1.375 1 0 to 2.048
1.25 to 3.00 2.181 0 to 4.46
2.5 to 6.0 4.363 0 to 6.0 1
6.0 to 14.4 10.472 0 to 14.4 1
1
VH pins.
The typical way to supply the reference to the ADC on the REFIN
pin is to connect the REFOUT pin to the REFIN pin. REFOUT
provides a 2.048 V reference. As such, the supervising range covers
less than half the normal ADC range. It is possible, however, to
provide the ADC with a more accurate external reference for
improved readback accuracy.
Supplies can also be connected to the input pins purely for ADC
readback, even though these pins may go above the expected
supervisory range limits (but not above the absolute maximum
NO ATTENUATION
DIGITIZED
VOLTAGE
READING
ratings on these pins). For example, a 1.5 V supply connected to
the VX1 pin can be correctly read out as an ADC code of approxi-
VXx
12-BIT
ADC
2.048V VREF
Figure 30. ADC Reading on VXx Pins
mately 3/4 full scale, but it always sits above any supervisory limits
that can be set on that pin. The maximum setting for the REFIN
pin is 2.048 V.
SUPPLY SUPERVISION WITH THE ADC
In addition to the readback capability, another level of supervision
VPx/VH
ATTENUATION NETWORK
(DEPENDS ON RANGE SELECTED)
12-BIT
ADC
DIGITIZED
VOLTAGE
READING
is provided by the on-chip 12-bit ADC. The ADM1166 has limit
registers with which the user can program a maximum or minimum
allowable threshold. Exceeding the threshold generates a warning
that can either be read back from the status registers or input
into the SE to determine what sequencing action the ADM1166
should take. Only one register is provided for each input channel.
2.048V VREF
Figure 31. ADC Reading on VPx/VH Pins
The voltage at the input pin can be derived from the following
equation:
Therefore, either an undervoltage threshold or overvoltage
threshold (but not both) can be set for a given channel. The
round-robin circuit can be enabled via a SMBus write, or it
can be programmed to turn on in any state in the SE program.
For example, it can be set to start after a power-up sequence is
V =
ADC Code
4095
× Attenuation Factor × V REFIN
complete and all supplies are known to be within expected
tolerance limits.
where V REFIN = 2.048 V when the internal reference is used (that
is, the REFIN pin is connected to the REFOUT pin).
The ADC input voltage ranges for the SFD input ranges are listed
Note that latency is built into this supervision, dictated by the
conversion time of the ADC. With all 12 channels selected, the
total time for the round-robin operation (averaging off) is
approximately 6 ms (500 μs per channel selected). Supervision
using the ADC, therefore, does not provide the same real-time
response as the SFDs.
Rev. 0 | Page 21 of 32
相关PDF资料 |
PDF描述 |
|---|---|
| 0982661057 | CBL 35POS 0.5MM JMPR TYPE A 3" |
| H3AAS-1406G | IDC CABLE - HSC14S/AE14G/HSC14S |
| V300B3V3E100B2 | CONVERTER MOD DC/DC 3.3V 100W |
| H2MXS-1406M | DIP CABLE - HDM14S/AE14M/X |
| GCM12DRYN-S13 | CONN EDGECARD 24POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1166ACPZ-REEL | 功能描述:IC SEQUENCER/SUPERVISOR 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1166ARTZ | 制造商:Analog Devices 功能描述:SUPER SEQUENCER W/ BLACK BOX - Tape and Reel |
| ADM1166ASUZ | 功能描述:IC SEQUENCER/SUPERVISOR 48TQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1166ASUZ-REEL | 功能描述:IC SEQUENCER/SUPERVISOR 48TQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1166ASUZ-REEL7 | 功能描述:IC SEQUENCER/SUPERVISOR 48TQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。