- 您现在的位置：买卖IC网 > PDF目录16806 > ADM1166ACPZ (Analog Devices Inc)IC SEQUENCER/SUPERVISOR 40LFCSP PDF资料下载
参数资料
| 型号： | ADM1166ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 30/32页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCER/SUPERVISOR 40LFCSP |
| 标准包装： | 1 |
| 系列： | Super Sequencer® |
| 应用： | 电源监控器，序列发生器 |
| 输入电压： | 3 V ~ 14.4 V |
| 电源电压： | 3 V ~ 14.4 V |
| 电流 - 电源： | 4.2mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-WQ（6x6） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页
ADM1166
Because a page consists of 32 bytes, only the three MSBs of
the address low byte are important for page erasure. The
lower five bits of the EEPROM address low byte specify the
Unlike some EEPROM devices that limit block writes to within
a page boundary, there is no limitation on the start address
when performing a block write to EEPROM, except when
addresses within a page and are ignored during an erase
operation.
?
There must be at least N locations from the start address to
the highest EEPROM address (0xFBFF) to avoid writing to
?
To write a single byte of data to the EEPROM. In this case,
invalid addresses.
the command byte is the high byte of EEPROM Address 0xF8
?
An address crosses a page boundary. In this case, both
to EEPROM Address 0xFB. The first data byte is the low
byte of the EEPROM address, and the second data byte is
pages must be erased before programming.
Note that the ADM1166 features a clock extend function for writes
to the EEPROM. Programming an EEPROM byte takes approxi-
1
S
2
SLAVE
ADDRESS
3
W A
4
EEPROM
ADDRESS
HIGH BYTE
(0xF8 TO 0xFB)
5
A
6
EEPROM
ADDRESS
LOW BYTE
(0x00 TO 0xFF)
7 8 9 10
A DATA A P
mately 250 μs, which limits the SMBus clock for repeated or block
write operations. The ADM1166 pulls SCL low and extends the
clock pulse when it cannot accept any more data.
Figure 43. Single Byte Write to the EEPROM
Block Write
In a block write operation, the master device writes a block of
data to a slave device. The start address for a block write must
have been set previously. In the ADM1166, a send byte opera-
tion sets a RAM address, and a write byte/word operation sets
READ OPERATIONS
The ADM1166 uses the following SMBus read protocols.
Receive Byte
In a receive byte operation, the master device receives a single
byte from a slave device, as follows:
an EEPROM address, as follows:
1.
The master device asserts a start condition on SDA.
1.
2.
3.
4.
The master device asserts a start condition on SDA.
The master sends the 7-bit slave address followed by
the write bit (low).
The addressed slave device asserts an ACK on SDA.
The master sends a command code that tells the slave
device to expect a block write. The ADM1166 command
code for a block write is 0xFC (1111 1100).
2.
3.
4.
5.
6.
The master sends the 7-bit slave address followed by the
read bit (high).
The addressed slave device asserts an ACK on SDA.
The master receives a data byte.
The master asserts a NACK on SDA.
The master asserts a stop condition on SDA, and the
transaction ends.
5.
6.
The slave asserts an ACK on SDA.
The master sends a data byte that tells the slave device how
many data bytes are being sent. The SMBus specification
allows a maximum of 32 data bytes in a block write.
In the ADM1166, the receive byte protocol is used to read a
single byte of data from a RAM or EEPROM location whose
address has previously been set by a send byte or write
7.
The slave asserts an ACK on SDA.
1
2
3
4
5
6
8.
9.
The master sends N data bytes.
The slave asserts an ACK on SDA after each data byte.
S
SLAVE
ADDRESS
R
A
DATA
A
P
10. The master asserts a stop condition on SDA to end the
transaction.
Figure 44. Single Byte Read from the EEPROM or RAM
1
2
3
4
5
6
7
8
9
10
S ADDRESS W A (BLOCK WRITE) A COUNT A
SLAVE COMMAND 0xFC BYTE
DATA
1
A
DATA
2
A
DATA
N
A P
Figure 45. Block Write to the EEPROM or RAM
Rev. 0 | Page 30 of 32
相关PDF资料 |
PDF描述 |
|---|---|
| 0982661057 | CBL 35POS 0.5MM JMPR TYPE A 3" |
| H3AAS-1406G | IDC CABLE - HSC14S/AE14G/HSC14S |
| V300B3V3E100B2 | CONVERTER MOD DC/DC 3.3V 100W |
| H2MXS-1406M | DIP CABLE - HDM14S/AE14M/X |
| GCM12DRYN-S13 | CONN EDGECARD 24POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1166ACPZ-REEL | 功能描述:IC SEQUENCER/SUPERVISOR 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1166ARTZ | 制造商:Analog Devices 功能描述:SUPER SEQUENCER W/ BLACK BOX - Tape and Reel |
| ADM1166ASUZ | 功能描述:IC SEQUENCER/SUPERVISOR 48TQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1166ASUZ-REEL | 功能描述:IC SEQUENCER/SUPERVISOR 48TQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1166ASUZ-REEL7 | 功能描述:IC SEQUENCER/SUPERVISOR 48TQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。