- 您现在的位置：买卖IC网 > PDF目录22117 > ADM1276-3ACPZ-RL (Analog Devices Inc)IC HOT SWAP CTLR PMBUS 20LFCSP PDF资料下载
参数资料
| 型号： | ADM1276-3ACPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 20/48页 |
| 文件大小： | 0K |
| 描述： | IC HOT SWAP CTLR PMBUS 20LFCSP |
| 标准包装： | 5,000 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | 2.95 V ~ 20 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WQFN 裸露焊盘，CSP |
| 供应商设备封装： | 20-LFCSP-WQ（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
ADM1276
VCAP
Data Sheet
FLB (see Figure 45). This change has minimal impact on startup
because the output voltage rises at a similar rate to the SS voltage.
C1
R1
SENSE+
SENSE–
ISET
ADM1276
+ –
×50
ADM1276
V CP
GATE
R2
DRIVE/
LOGIC
GATE
GND
ISET
VCAP
REF
SELECT
1.0V
+
–
TIMEOUT
CURRENT
LIMIT
CURRENT
Figure 47. Adjustable 5 mV to 25 mV Current Sense Limit
LIMIT
The VCAP pin has a 2.7 V internal generated voltage that can
be used to set a voltage at the ISET pin. Assuming that V ISET
SS
10μA
CURRENT
LIMIT
CONTROL
FLB
equals the voltage on the ISET pin, size the resistor divider to
I SS ? t
set the ISET voltage as follows:
V ISET = V SENSE × 50
where V SENSE is the current sense voltage limit.
The VCAP rail can also be used as the pull-up supply for setting
the I 2 C address. Do not use the VCAP pin for any other purpose.
To guarantee accuracy specifications, do not load the VCAP pin
by more than 100 μA.
SOFT START
A capacitor connected to the SS pin determines the inrush current
profile. Before the FET is enabled, the output voltage of the
current-limit reference selector block is clamped at 100 mV.
This, in turn, holds the hot swap sense voltage current limit,
V SENSECL , at approximately 2 mV. When the FET receives a
request to turn on, the SS pin is held at ground until the voltage
between the SENSE+ and SENSE? pins (V SENSE ) reaches the
circuit breaker voltage, V CB .
V CB = V SENSECL ? V CBOS
where V CBOS is typically 0.88 mV, making V CB = 1.12 mV.
When the load current generates a sense voltage equal to V CB ,
a 10 μA current source is enabled, which charges the SS capa-
citor and results in a linear ramping voltage on the SS pin. The
current-limit reference also ramps up accordingly, allowing the
regulated load current to ramp up while avoiding sudden transients
during power-up. The SS capacitor value is given by
C SS ?
V ISET
where:
I SS = 10 μA.
t = SS ramp time.
For example, a 10 nF capacitor gives a soft start time of 1 ms.
Note that the SS voltage may intersect with the FLB (foldback)
voltage, and the current-limit reference may change to follow
GND
Figure 48. Soft Start
FOLDBACK
Foldback is a method to actively reduce the current limit as the
voltage drop across the FET increases. It keeps the power across
the FET to a minimum during power-up, overcurrent, or short-
circuit events. It also avoids the need to oversize the FET to
accommodate worst-case conditions, resulting in board size
and cost savings.
The ADM1276 detects the voltage drop across the FET by
looking at a resistor divided version of the output voltage. It is
assumed that the supply voltage remains constant and within
tolerance. The device, therefore, relies on the principle that the
drain of the FET is at the maximum expected supply voltage,
and that the magnitude of the output voltage is relative to that
of the V DS of the FET. Using a resistor divider from the output
voltage to the FLB pin, a relationship from V OUT , and thus V DS ,
to V FLB can be derived.
Design the resistor divider to output a voltage equal to ISET
when V OUT falls below the desired level. This should be well
below the working tolerance of the supply rail. As V OUT continues
to drop, the current-limit reference follows V FLB because it is
now the lowest voltage input to the current-limit reference
selector block. This results in a reduction of the current limit
and, therefore, the regulated load current. To prevent complete
current flow restriction, a clamp becomes active when the
current-limit reference reaches 200 mV. The current limit
cannot drop below this level.
To suit the SOA characteristics of a particular FET, the required
minimum current for this clamp varies from design to design.
However, the current-limit reference fixes this clamp at 200 mV,
which equates to 4 mV at the sense resistor. Therefore, the main
ISET voltage can be adjusted to align this clamp to the required
percentage current reduction. For example, if ISET equals 0.8 V,
the clamp can be set at 25% of the maximum current.
Rev. C | Page 20 of 48
相关PDF资料 |
PDF描述 |
|---|---|
| R05P205S/P | CONV DC/DC 2W 05VIN 05VOUT |
| VI-22Y-CX-F2 | CONVERTER MOD DC/DC 3.3V 49.5W |
| 2-530666-6 | CONN LOW PRO 22 POS 156X200C/L |
| ESC08DRYS | CONN EDGECARD 16POS DIP .100 SLD |
| MIC2586R-2YM | IC CTRLR/SEQ HOT SWAP 14-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1278-1AACPZ | 功能描述:Hot Swap Controller, Monitor 1 Channel General Purpose 32-LFCSP (5x5) 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:有效 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP（5x5） 功能引脚:- 标准包装:1 |
| ADM1278-1AACPZ-RL | 功能描述:Hot Swap Controller, Monitor 1 Channel General Purpose 32-LFCSP-WQ (5x5) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:有效 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP-WQ（5x5） 功能引脚:- 标准包装:5,000 |
| ADM1278-1ACPZ | 功能描述:Hot Swap Controller, Monitor 1 Channel General Purpose 32-LFCSP (5x5) 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:有效 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP（5x5） 功能引脚:- 标准包装:1 |
| ADM1278-1ACPZ-RL | 功能描述:IC ENERGY MON HOT-SWAP 32-LFCSP 制造商:analog devices inc. 系列:- 包装:剪切带（CT） 零件状态:在售 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP-WQ（5x5） 功能引脚:- 标准包装:1 |
| ADM1278-1BCPZ | 功能描述:Hot Swap Controller, Monitor 1 Channel General Purpose 32-LFCSP (5x5) 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:有效 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP（5x5） 功能引脚:- 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。