- 您现在的位置：买卖IC网 > PDF目录22117 > ADM1276-3ACPZ-RL (Analog Devices Inc)IC HOT SWAP CTLR PMBUS 20LFCSP PDF资料下载
参数资料
| 型号： | ADM1276-3ACPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 33/48页 |
| 文件大小： | 0K |
| 描述： | IC HOT SWAP CTLR PMBUS 20LFCSP |
| 标准包装： | 5,000 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | 2.95 V ~ 20 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WQFN 裸露焊盘，CSP |
| 供应商设备封装： | 20-LFCSP-WQ（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
Data Sheet
GPO2/ALERT2 PIN BEHAVIOR
The ADM1276 provides a very flexible alert system, whereby
one or more fault/warning conditions can be indicated to an
external device.
FAULTS AND WARNINGS
ADM1276
the GPO2/ALERT2 pin active. By default, the active state of the
GPO2/ALERT2 pin is low.
For example, to use GPO2/ALERT2 to monitor the VOUT UV
warning from the ADC, the followings steps must be performed:
A PMBus fault on the ADM1276 is always generated due to an
analog event and causes a change in state in the hot swap output,
turning it off. The three defined fault sources are as follows:
1.
2.
Set a threshold level with the VOUT_UV_WARN_LIMIT
command.
Start the power monitor sampling on VOUT.
?
?
?
Undervoltage (UV) event detected on the UV pin.
Overvoltage (OV) event detected on the OV pin.
Overcurrent (OC) event that causes a hot swap timeout.
If a VOUT sample is taken that is below the configured
VOUT UV value, the GPO2/ALERT2 pin is taken low, signaling
an interrupt to a processor.
Faults are continuously monitored, and, as long as power is
applied to the device, they cannot be disabled. When a fault
occurs, a corresponding status bit is set in one or more
STATUS_xxx registers.
A value of 1 in a status register bit field always indicates a fault
or warning condition. Fault and warning bits in the status
registers are latched when set to 1. To clear a latched bit to 0—
HANDLING/CLEARING AN ALERT
When faults/warnings are configured on the GPO2/ALERT2 pin,
the pin becomes active to signal an interrupt to the processor.
(The pin is active low, unless inversion is enabled.) The ALERT2
signal on the GPO2/ALERT2 pin functions as an SMBAlert.
A processor can respond to the interrupt in one of two basic ways:
provided that the fault condition is no longer active—use the
CLEAR_FAULTS command or use the OPERATION command
to turn the hot swap output off and then on again.
A warning is less severe than a fault and never causes a change
in the state of the hot swap controller. The sources of a warning
are defined as follows:
? CML: a communications error occurred on the I 2 C bus.
? HS timer was active (HSTA): the current regulation was
active, but did not necessarily shut the system down.
? IOUT OC warning from the ADC.
? IOUT Warning 2 from the ADC.
? VIN UV warning from the ADC.
? VIN OV warning from the ADC.
? VOUT UV warning from the ADC.
? VOUT OV warning from the ADC.
? PIN OP warning from the VIN × IOUT calculation.
?
?
If there is only one device on the bus, the processor can
simply read the status bytes and issue a CLEAR_FAULTS
command to clear all the status bits, which causes the deas-
sertion of the GPO2/ALERT2 line. If there is a persistent
fault—for example, an undervoltage on the input—the
status bits remain set after the CLEAR_FAULTS command
is executed because the fault has not been removed. However,
the GPO2/ALERT2 line is not pulled low unless a new fault
or warning becomes active. If the cause of the SMBAlert is
a power monitor generated warning and the power monitor
is running continuously, the next sample generates a new
SMBAlert after the CLEAR_FAULTS command is issued.
If there are several devices on the bus, the processor can
issue an SMBus alert response address command to find
out which device asserted the SMBAlert line. The processor
can read the status bytes from that device and issue a
CLEAR_FAULTS command.
GENERATING AN ALERT
A host device can periodically poll the ADM1276 using the
status commands to determine whether a fault/warning is
active. However, this polling is very inefficient in terms of
software and processor resources. The ADM1276 has a
GPO2/ALERT2 output pin that can be used to generate
interrupts to a host processor.
By default at power-up, the open-drain GPO2/ALERT2
output is high impedance, so the pin can be pulled high
through a resistor. The FET health bad warning is active by
default on the GPO2/ALERT2 pin at power-up.
Any one or more of the faults and warnings listed in the Faults
SMBus ALERT RESPONSE ADDRESS
The SMBus alert response address (ARA) is a special address
that can be used by the bus host to locate any devices that need
to talk to it. A host typically uses a hardware interrupt pin to
monitor the SMBus alert pins of a number of devices. When the
host interrupt occurs, the host issues a message on the bus using
the SMBus receive byte or receive byte with PEC protocol.
The special address used by the host is 0x0C. Any devices that
have an SMBAlert signal return their own 7-bit address as the
seven MSBs of the data byte. The LSB value is not used and can
be either 1 or 0. The host reads the device address from the
received data byte and proceeds to handle the alert condition.
Rev. C | Page 33 of 48
相关PDF资料 |
PDF描述 |
|---|---|
| R05P205S/P | CONV DC/DC 2W 05VIN 05VOUT |
| VI-22Y-CX-F2 | CONVERTER MOD DC/DC 3.3V 49.5W |
| 2-530666-6 | CONN LOW PRO 22 POS 156X200C/L |
| ESC08DRYS | CONN EDGECARD 16POS DIP .100 SLD |
| MIC2586R-2YM | IC CTRLR/SEQ HOT SWAP 14-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1278-1AACPZ | 功能描述:Hot Swap Controller, Monitor 1 Channel General Purpose 32-LFCSP (5x5) 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:有效 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP（5x5） 功能引脚:- 标准包装:1 |
| ADM1278-1AACPZ-RL | 功能描述:Hot Swap Controller, Monitor 1 Channel General Purpose 32-LFCSP-WQ (5x5) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:有效 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP-WQ（5x5） 功能引脚:- 标准包装:5,000 |
| ADM1278-1ACPZ | 功能描述:Hot Swap Controller, Monitor 1 Channel General Purpose 32-LFCSP (5x5) 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:有效 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP（5x5） 功能引脚:- 标准包装:1 |
| ADM1278-1ACPZ-RL | 功能描述:IC ENERGY MON HOT-SWAP 32-LFCSP 制造商:analog devices inc. 系列:- 包装:剪切带（CT） 零件状态:在售 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP-WQ（5x5） 功能引脚:- 标准包装:1 |
| ADM1278-1BCPZ | 功能描述:Hot Swap Controller, Monitor 1 Channel General Purpose 32-LFCSP (5x5) 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:有效 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP（5x5） 功能引脚:- 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。