- 您现在的位置：买卖IC网 > PDF目录22117 > ADM1276-3ACPZ-RL (Analog Devices Inc)IC HOT SWAP CTLR PMBUS 20LFCSP PDF资料下载
参数资料
| 型号： | ADM1276-3ACPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 29/48页 |
| 文件大小： | 0K |
| 描述： | IC HOT SWAP CTLR PMBUS 20LFCSP |
| 标准包装： | 5,000 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | 2.95 V ~ 20 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WQFN 裸露焊盘，CSP |
| 供应商设备封装： | 20-LFCSP-WQ（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
Data Sheet
The power monitor can measure the following quantities:
ADM1276
Each time a power calculation is done, the 24-bit power value is
?
?
?
Input voltage (VIN).
Output voltage (VOUT).
Output current (IOUT).
added to a 24-bit energy accumulator register. This is a twos
complement representation as well, so the MSB is always zero.
Each time this energy accumulator register rolls over from
0x7FFFFF to 0x000000, a 16-bit rollover counter is
The following quantities are then calculated:
? Input power (PIN).
? Input energy (EIN).
PMON_CONFIG Command
The power monitor can run in a number of different modes with
different input voltage range settings. The PMON_CONFIG
command is used to set up the power monitor.
The settings that can be configured are as follows:
? Single shot or continuous sampling.
? VOUT sampling enable/disable.
? Voltage input range.
? Current and voltage sample averaging.
Modifying the power monitor settings while the power monitor
is sampling is not recommended. To ensure correct operation of
the device and to avoid any potential spurious data or the
generation of status alerts, stop the power monitor before any of
these settings are changed.
PMON_CONTROL Command
Power monitor sampling can be initiated via hardware or via
software using the PMON_CONTROL command. This command
can be used with single shot or continuous mode.
READ_VIN, READ_VOUT, and READ_IOUT Commands
The ADM1276 power monitor measures the voltage developed
across the sense resistor to provide a current measurement. The
input voltage from the SENSE+ pin is always measured, and the
output voltage present on the VOUT pin is available if enabled
with the PMON_CONFIG command.
READ_PIN, READ_PIN_EXT, READ_EIN, and
READ_EIN_EXT Commands
The 12-bit VIN input voltage and 12-bit IOUT current measure-
ment values are multiplied by the ADM1276 to give the input
power value. This is accomplished by using fixed point
arithmetic, and produces a 24-bit value. It is assumed that the
numbers are in the 12.0 format, meaning that there is no
fractional part. Note that only positive IOUT values are used to
avoid returning a negative power.
This 24-bit value can be read from the ADM1276 using the
READ_PIN_EXT command, where the most significant bit
(MSB) is always a zero because PIN_EXT is a twos complement
binary value that is always positive.
The sixteen most significant bits of the 24-bit value are used as
the value for PIN. The MSB of the 16-bit PIN word is always
zero, as PIN is a twos complement binary value, that is always
positive.
incremented. The rollover counter is straight binary, with a
maximum value of 0xFFFF before it rolls over.
A 24-bit straight binary power sample counter is also
incremented by 1 each time a power value is calculated and
added to the energy accumulator.
These registers can be read back using one of two commands,
depending on the level of accuracy required for the energy
accumulator and the desire to limit the frequency of reads from
A bus host can read these values, and by calculating the delta in
the energy accumulated, the delta in the number of samples,
and the time delta since the last read, the host can calculate the
average power since the last read, as well as the energy
consumed since then.
The time delta is calculated by the bus host based on when it
sends its commands to read from the device, and is not
To avoid loss of data, the bus host must read at a rate that
ensures the rollover counter does not wrap around more than
once, and if the counter does wrap around that the next value
read for PIN is less than the previous one.
The READ_EIN command returns the top 16 bits of the energy
accumulator, the lower eight bits of the rollover counter, and the
full 24 bits of the sample counter.
The READ_EIN_EXT command returns the full 24 bits of the
energy accumulator, the full 16 bits of the rollover counter, and
the full 24 bits of the sample counter. The use of the longer
rollover counter means that the time interval between reads of
the part can be increased from seconds to minutes, without
losing any data.
PEAK_IOUT, PEAK_VIN, PEAK_VOUT, and PEAK_PIN
Commands
In addition to the standard PMBus commands for reading
voltage and current, the ADM1276 provides commands that
can report the maximum peak voltage, current, or power value
since the peak value was last cleared.
The peak values are updated only after the power monitor has
sampled and averaged the current and voltage measurements.
Individual peak values are cleared by writing a 0 value with the
corresponding command.
WARNING LIMIT SETUP COMMANDS
The ADM1276 power monitor can monitor a number of
different warning conditions simultaneously and report any
current or voltage values that exceed the user-defined
thresholds using the status commands.
Rev. C | Page 29 of 48
相关PDF资料 |
PDF描述 |
|---|---|
| R05P205S/P | CONV DC/DC 2W 05VIN 05VOUT |
| VI-22Y-CX-F2 | CONVERTER MOD DC/DC 3.3V 49.5W |
| 2-530666-6 | CONN LOW PRO 22 POS 156X200C/L |
| ESC08DRYS | CONN EDGECARD 16POS DIP .100 SLD |
| MIC2586R-2YM | IC CTRLR/SEQ HOT SWAP 14-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1278-1AACPZ | 功能描述:Hot Swap Controller, Monitor 1 Channel General Purpose 32-LFCSP (5x5) 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:有效 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP（5x5） 功能引脚:- 标准包装:1 |
| ADM1278-1AACPZ-RL | 功能描述:Hot Swap Controller, Monitor 1 Channel General Purpose 32-LFCSP-WQ (5x5) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:有效 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP-WQ（5x5） 功能引脚:- 标准包装:5,000 |
| ADM1278-1ACPZ | 功能描述:Hot Swap Controller, Monitor 1 Channel General Purpose 32-LFCSP (5x5) 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:有效 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP（5x5） 功能引脚:- 标准包装:1 |
| ADM1278-1ACPZ-RL | 功能描述:IC ENERGY MON HOT-SWAP 32-LFCSP 制造商:analog devices inc. 系列:- 包装:剪切带（CT） 零件状态:在售 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP-WQ（5x5） 功能引脚:- 标准包装:1 |
| ADM1278-1BCPZ | 功能描述:Hot Swap Controller, Monitor 1 Channel General Purpose 32-LFCSP (5x5) 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:有效 类型:热交换控制器，监控器 通道数:1 内部开关:无 应用:通用 特性:PMBus 可编程特性:自动重试，限流，故障超时，闭锁故障，OVP，压摆率，UVLO 电压 - 电源:4.5 V ~ 20 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:5.5mA 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘，CSP 供应商器件封装:32-LFCSP（5x5） 功能引脚:- 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。