- 您现在的位置：买卖IC网 > PDF目录11203 > ADUC7128BSTZ126-RL (Analog Devices Inc)IC DAS MCU ARM7 ADC/DDS 64-LQFP PDF资料下载
参数资料
| 型号： | ADUC7128BSTZ126-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 60/92页 |
| 文件大小： | 0K |
| 描述： | IC DAS MCU ARM7 ADC/DDS 64-LQFP |
| 产品培训模块： | ARM7 Applications & Tools Intro to ARM7 Core & Microconverters Process Control Direct Digital Synthesis Tutorial Series (1 of 7): Introduction |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 41.78MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | PLA，POR，PWM，PSM，温度传感器，WDT |
| 输入/输出数： | 28 |
| 程序存储器容量： | 126KB（63K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 8K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 3 V ~ 3.6 V |
| 数据转换器： | A/D 10x12b; D/A 1x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 64-LQFP |
| 包装： | 标准包装 |
| 配用： | EVAL-ADUC7128QSPZ-ND - KIT DEV FOR ADUC7128 |
| 其它名称： | ADUC7128BSTZ126-RLDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页当前第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
ADuC7128/ADuC7129
Rev. 0 | Page 63 of 92
SERIAL PERIPHERAL INTERFACE
The ADuC7128/ADuC7129 integrate a complete hardware
serial peripheral interface (SPI) on-chip. SPI is an industry-
standard synchronous serial interface that allows eight bits
of data to be synchronously transmitted and simultaneously
received, that is, full duplex up to a maximum bit rate of 3.4 Mbs.
The SPI interface is operational only with core clock divider
bits POWCON[2:0] = 0, 1, or 2.
The SPI port can be configured for master or slave operation and
typically consists of four pins, namely: MISO, MOSI, SCL, and CS.
MISO (Master In, Slave Out) Data I/O Pin
The MISO pin is configured as an input line in master mode
and an output line in slave mode. The MISO line on the master
(data in) should be connected to the MISO line in the slave
device (data out). The data is transferred as byte wide (8-bit)
serial data, MSB first.
MOSI (Master Out, Slave In) Pin
The MOSI pin is configured as an output line in master mode
and an input line in slave mode. The MOSI line on the master
(data out) should be connected to the MOSI line in the slave
device (data in). The data is transferred as byte wide (8-bit)
serial data, MSB first.
SCL (Serial Clock) I/O Pin
The master serial clock (SCL) is used to synchronize the data
being transmitted and received through the MOSI SCL period.
Therefore, a byte is transmitted/received after eight SCL periods.
The SCL pin is configured as an output in master mode and as
an input in slave mode.
In master mode, polarity and phase of the clock are controlled
by the SPICON register, and the bit rate is defined in the
SPIDIV register as follows:
)
1
(
2
SPIDIV
f
HCLK
CLOCK
SERIAL
+
×
=
In slave mode, the SPICON register must be configured with
the phase and polarity of the expected input clock. The slave
accepts data from an external master up to 3.4 Mbs at CD = 0.
In both master and slave modes, data is transmitted on one edge
of the SCL signal and sampled on the other. Therefore, it is
important that the polarity and phase be configured the same
for the master and slave devices.
The maximum speed of the SPI clock is dependent on the clock
divider bits and is summarized in Table 89.
Table 89. SPI Speed vs. Clock Divider Bits in Master Mode
CD Bits
0
1
2
3
4
5
SPIDIV in hex
0x05
0x0B
0x17
0x2F
0x5F
0xBF
SPI speed
in MHz
3.482
1.741
0.870
0.435
0.218
0.109
In slave mode, the SPICON register must be configured with
the phase and polarity of the expected input clock. The slave
accepts data from an external master up to 10.4 Mbs at CD = 0.
The formula to determine the maximum speed follows:
4
HCLK
CLOCK
SERIAL
f
=
In both master and slave modes, data is transmitted on one edge
of the SCL signal and sampled on the other. Therefore, it is
important that the polarity and phase be configured the same
for the master and slave devices.
Chip Select (CS) Input Pin
In SPI slave mode, a transfer is initiated by the assertion of CS,
which is an active low input signal. The SPI port then transmits
and receives 8-bit data until the transfer is concluded by
desassertion of CS. In slave mode, CS is always an input.
SPI Registers
The following MMR registers are used to control the SPI
interface: SPISTA, SPIRX, SPITX, SPIDIV, and SPICON.
SPISTA Register
Name
Address
Default Value
Access
SPISTA
0xFFFF0A00
0x00
R
SPISTA is an 8-bit read-only status register.
Table 90. SPISTA MMR Bit Designations
Bit
Description
7:6
Reserved.
5
SPIRX Data Register Overflow Status Bit.
Set if SPIRX is overflowing.
Cleared by reading SPIRX register.
4
SPIRX Data Register IRQ.
Set automatically if Bit 3 or Bit 5 is set.
Cleared by reading SPIRX register.
3
SPIRX Data Register Full Status Bit.
Set automatically if valid data is present in the SPIRX
register.
Cleared by reading SPIRX register.
2
SPITX Data Register Underflow Status Bit.
Set automatically if SPITX is underflowing.
Cleared by writing in the SPITX register.
1
SPITX Data Register IRQ.
Set automatically if Bit 0 is clear or Bit 2 is set.
Cleared by writing in the SPITX register or if finished
transmission disabling the SPI.
0
SPITX Data Register Empty Status Bit.
Set by writing to SPITX to send data. This bit is set
during transmission of data.
Cleared when SPITX is empty.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-BTJ-IX | CONVERTER MOD DC/DC 36V 75W |
| VI-BTJ-IW | CONVERTER MOD DC/DC 36V 100W |
| VI-BTH-IX | CONVERTER MOD DC/DC 52V 75W |
| AT91SAM7X256B-CU-999 | IC MCU ARM 256KB FLASH 100TFBGA |
| VI-BT4-IW | CONVERTER MOD DC/DC 48V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC7128BSTZ126-RL2 | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Analog Microcontroller ARM7TDMI MCU with 12-Bit ADC and DDS DAC |
| ADUC7129 | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Analog Microcontroller ARM7TDMI MCU with 12-Bit ADC and DDS DAC |
| ADUC7129BSTZ126 | 功能描述:IC DAS MCU ARM7 ADC/DDS 80-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC7129BSTZ1262 | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Analog Microcontroller ARM7TDMI MCU with 12-Bit ADC and DDS DAC |
| ADUC7129BSTZ126-RL | 功能描述:IC DAS MCU ARM7 ADC/DDS 80-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 产品培训模块:Graphics LCD System and PIC24 Interface Asynchronous Stimulus 标准包装:27 系列:PIC® 24H 核心处理器:PIC 芯体尺寸:16-位 速度:40 MIP 连通性:I²C，SPI，UART/USART 外围设备:欠压检测/复位，POR，PWM，WDT 输入/输出数:21 程序存储器容量:12KB（4K x 24） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):3 V ~ 3.6 V 数据转换器:A/D 10x10b/12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 包装:管件 产品目录页面:648 (CN2011-ZH PDF) 配用:AC164339-ND - MODULE SKT FOR PM3 28SOICDV164033-ND - KIT START EXPLORER 16 MPLAB ICD2 |
发布紧急采购，3分钟左右您将得到回复。