- 您现在的位置：买卖IC网 > Datasheet目录667 > AP033 (Teledyne LeCroy)PROBE DIFFERENTIAL 500MHZ Datasheet资料下载
参数资料
| 型号： | AP033 |
| 厂商： | Teledyne LeCroy |
| 文件页数： | 15/62页 |
| 文件大小： | 0K |
| 描述： | PROBE DIFFERENTIAL 500MHZ |
| 产品培训模块： | Fundamentals of Probing Overview |
| 标准包装： | 1 |
| 系列： | AP |
| 类型： | 有源差分 |
| 衰减值： | 1:1，10:1 |
| 带宽： | 500MHz |
| 电阻 - 输入： | 2M |
| 电压 - 最大： | CAT I 42.4V |
| 电容 - 输入： | 2.7pF，1.2pF |
| 线缆长度： | 42.000"（1066.80mm） |
| 颜色： | 灰 |
| 包括： | AC 耦合器，附件工具包，衰减器，外壳，手册 |
| 配用： | MSO 44MXS-B-ND - DGTL O-SCOPE MIX SGL 400MHZ DSO MSO 64MXS-B-ND - DGTL O-SCOPE MIX SGL 600MHZ DSO MSO 104MXS-B-ND - DGTL O-SCOPE MIX SGL 1GHZ DSO WAVESURFER 104MXS-B-ND - DGTL O-SCOPE 1GHZ 5GS/S 4CH WAVESURFER 64MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 4CH WAVESURFER 62MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 2CH WAVESURFER 44MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 4CH WAVESURFER 42MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 2CH WAVESURFER 24MXS-B-ND - DGTL O-SCOPE 200MHZ 2.5GS/S 4CH |
| 相关产品： | PK033-ND - AP033/AP034 ACCES KIT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
Operator’s Manual
can greatly reduce this effect by using short interconnection leads, and twisting them together to
minimize the loop area.
High common mode rejection requires precise matching of the relative gain or attenuation in the +
and – input signal paths. Mismatches in additional parasitic capacitance, inductance, delay, and a
source impedance difference between the + and – signal paths will lower the common mode
rejection ratio. Therefore, it is desirable to use the same length and type of wire and connectors for
both input connections. When possible, try to connect the inputs to points in the circuit with
approximately the same source impedance.
If AC coupling is desired, install the AC coupling accessory on the probe tip before connecting it to
the test circuit. The low-frequency cutoff ( – 3 dB point) of the AC coupler is approximately 16 Hz.
If the voltage in the test circuit requires more than ÷10 attentuation, add the external ÷10
attenuator to the probe tip. If using both the external attenuator and AC coupler, install the
attenuator on the probe tip first, then install the AC coupler on the attenuator input.
In addition to being compatible with the included lead set, the probe input connectors will mate
with standard 0.025 in. (0.635 mm) square pins in any rotational orientation. To avoid damaging
the input connectors, do not attempt to insert connectors or wire larger than 0.036 in. (0.91 mm) in
diameter. Avoid rotating square pins after they are inserted into the input connectors.
The included accessories simplify the task of connecting the probe to the test circuit:
?
?
?
Use the small (0.5 mm) mini clips with the flexible lead set when connecting to fine-pitch
surface mount IC leads .
Use the larger (0.8 mm) mini clips to connect to through-hole leaded components.
Use the offset round pins for hand-held probing applications. Reposition the pins by
rotating them to obtain the required spacing.
922260-00 Rev A
9
相关PDF资料 |
PDF描述 |
|---|---|
| AP034 | PROBE ACT DIFFERENTIAL 1GHZ |
| AP2S2LC | OSCILLATOR PROG 1.8V +-50PPM SMD |
| AP3S1EJ | OSCILLATOR PROG 2.5V +-20PPM SMD |
| APGDT001 | SYSTEM DEV LIN SERIAL ANALYZER |
| ARE0810KS04 | SWITCH DIP SPST EXTENDED 8POS SM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AP033 | 制造商:Lecroy Corporation 功能描述:DIFF. PROBE 500MHZ ((NS)) |
| AP-033/A/N | 制造商:MISCELLANEOUS 功能描述: |
| AP0332 | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
| AP0332CG | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
| AP0332ND | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
发布紧急采购，3分钟左右您将得到回复。