- 您现在的位置：买卖IC网 > Datasheet目录667 > AP033 (Teledyne LeCroy)PROBE DIFFERENTIAL 500MHZ Datasheet资料下载
参数资料
| 型号： | AP033 |
| 厂商： | Teledyne LeCroy |
| 文件页数： | 39/62页 |
| 文件大小： | 0K |
| 描述： | PROBE DIFFERENTIAL 500MHZ |
| 产品培训模块： | Fundamentals of Probing Overview |
| 标准包装： | 1 |
| 系列： | AP |
| 类型： | 有源差分 |
| 衰减值： | 1:1，10:1 |
| 带宽： | 500MHz |
| 电阻 - 输入： | 2M |
| 电压 - 最大： | CAT I 42.4V |
| 电容 - 输入： | 2.7pF，1.2pF |
| 线缆长度： | 42.000"（1066.80mm） |
| 颜色： | 灰 |
| 包括： | AC 耦合器，附件工具包，衰减器，外壳，手册 |
| 配用： | MSO 44MXS-B-ND - DGTL O-SCOPE MIX SGL 400MHZ DSO MSO 64MXS-B-ND - DGTL O-SCOPE MIX SGL 600MHZ DSO MSO 104MXS-B-ND - DGTL O-SCOPE MIX SGL 1GHZ DSO WAVESURFER 104MXS-B-ND - DGTL O-SCOPE 1GHZ 5GS/S 4CH WAVESURFER 64MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 4CH WAVESURFER 62MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 2CH WAVESURFER 44MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 4CH WAVESURFER 42MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 2CH WAVESURFER 24MXS-B-ND - DGTL O-SCOPE 200MHZ 2.5GS/S 4CH |
| 相关产品： | PK033-ND - AP033/AP034 ACCES KIT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
Operator’s Manual
9. Calculate the Common Mode Rejection Ratio (CMRR) at 70 Hz by dividing 8,000 mV by the
measured Common Mode Signal recorded in step C-8 (direct reciprocal of the Common Mode
Gain). Record the result to two-digit resolution (xx,000 : 1) in the Test Record.
10. Verify that the Common Mode Rejection Ratio at 70 Hz is greater than 3,160:1 (70 dB).
11. Set the oscilloscope to display channel 2. Change the horizontal scale factor to 0.5 s/division.
Set the BWL on channels 1 and 2 to 200 MHz.
12. Change the frequency of the Function Generator to 1 MHz.
13. Adjust the trigger level as necessary for a stable display. Adjust the Function Generator
amplitude as needed to maintain 8.0V pk-pk as measured on channel 2.
14. Turn off the oscilloscope channel 2 display; turn on the display of channel 1 and Math
waveform A (averaged channel 1). Adjust the scale factor of channel 1 and the Zoom of Math A
as necessary to accurately measure the amplitude of the averaged waveform.
15. Record the displayed ‘Common Mode Signal at 1 MHz’ to two -digit resolution in the Test
Record.
16. Calculate the Common Mode Rejection Ratio (CMRR) at 1 MHz by dividing 8,000 mV by the
measured Common Mode Signal recorded in step C-22. Record the result in the Test Record.
17. Verify that the Common Mode Rejection Ratio at 1 MHz is greater than 1,000:1 (60 dB).
18. Remove all cables and test fixtures from the AP033 probe.
This concludes the Performance Verification of the AP033. Complete and file the results recorded
in the AP033 Performance Verification Test Record as required by your quality procedures. Apply a
suitable calibration label to the AP033 housing as required.
AP033 Performance Verification Test Record
This record can be used to record the results of measurements made during the performance
verification of the AP033 Active Differential Probe.
Photocopy the next page and record the results on the copy. File the completed record as required
by applicable internal quality procedures.
The section in the test record corresponds to the parameters tested in the performance verification
procedure. The numbers preceding the individual data records correspond to the steps in the
procedure that require the recording of data. Results to be recorded in the column labeled “Test
Result” are the actual specification limit check. The test limits are included in all of these steps.
Other measurements and the results of intermediate calculations that support the limit check are
to be recorded in the column labeled “Intermediate Results.”
Permission is granted to reproduce these pages for the purpose of recording test results.
922260-00 Rev A
33
相关PDF资料 |
PDF描述 |
|---|---|
| AP034 | PROBE ACT DIFFERENTIAL 1GHZ |
| AP2S2LC | OSCILLATOR PROG 1.8V +-50PPM SMD |
| AP3S1EJ | OSCILLATOR PROG 2.5V +-20PPM SMD |
| APGDT001 | SYSTEM DEV LIN SERIAL ANALYZER |
| ARE0810KS04 | SWITCH DIP SPST EXTENDED 8POS SM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AP033 | 制造商:Lecroy Corporation 功能描述:DIFF. PROBE 500MHZ ((NS)) |
| AP-033/A/N | 制造商:MISCELLANEOUS 功能描述: |
| AP0332 | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
| AP0332CG | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
| AP0332ND | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
发布紧急采购，3分钟左右您将得到回复。