- 您现在的位置：买卖IC网 > Datasheet目录667 > AP033 (Teledyne LeCroy)PROBE DIFFERENTIAL 500MHZ Datasheet资料下载
参数资料
| 型号： | AP033 |
| 厂商： | Teledyne LeCroy |
| 文件页数： | 19/62页 |
| 文件大小： | 0K |
| 描述： | PROBE DIFFERENTIAL 500MHZ |
| 产品培训模块： | Fundamentals of Probing Overview |
| 标准包装： | 1 |
| 系列： | AP |
| 类型： | 有源差分 |
| 衰减值： | 1:1，10:1 |
| 带宽： | 500MHz |
| 电阻 - 输入： | 2M |
| 电压 - 最大： | CAT I 42.4V |
| 电容 - 输入： | 2.7pF，1.2pF |
| 线缆长度： | 42.000"（1066.80mm） |
| 颜色： | 灰 |
| 包括： | AC 耦合器，附件工具包，衰减器，外壳，手册 |
| 配用： | MSO 44MXS-B-ND - DGTL O-SCOPE MIX SGL 400MHZ DSO MSO 64MXS-B-ND - DGTL O-SCOPE MIX SGL 600MHZ DSO MSO 104MXS-B-ND - DGTL O-SCOPE MIX SGL 1GHZ DSO WAVESURFER 104MXS-B-ND - DGTL O-SCOPE 1GHZ 5GS/S 4CH WAVESURFER 64MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 4CH WAVESURFER 62MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 2CH WAVESURFER 44MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 4CH WAVESURFER 42MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 2CH WAVESURFER 24MXS-B-ND - DGTL O-SCOPE 200MHZ 2.5GS/S 4CH |
| 相关产品： | PK033-ND - AP033/AP034 ACCES KIT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
Operator’s Manual
With oscilloscope software versions 7.6.0 and higher, the probe gain, internal attenuation, and
offset can be conveniently controlled through the oscilloscope’s user interface. The common mode
range is also displayed. Manual control through the oscilloscope user interface can be found in the
COUPLING menu or the Channel dialog of the channel to which the probe is connected. The
appearance and functionality of the control menu has changed with incremental versions of the
oscilloscope software.
With software versions 8.1.0 and higher, there are two modes of gain control: Auto and Manual.
The oscilloscope defaults to Auto mode when the probe is first attached. In Auto mode, the
VOLTS/DIV knob controls the oscilloscope’s scale factor, AP033 gain, and AP033 attenuation to give
the full available dynamic range: 200 μV/div to 1 V/div (without external attenuator), or 2 mV/div
to 10 V/div (with external ? ÷ ??? attenuator installed). Some of the transitions in scale factor will
result in a change of the attenuation in the AP033 probe. The common mode range, input
capacitance, and noise level of the probe will change with the probe attenuator setting. For
Volts/Div settings which can be produced with more than one combination of probe gain and
attenuation settings, Auto mode selects the combination which results in greater common mode
range and lower input capacitance.
In some situations, you may wish to select probe settings optimized for the lowest noise
performance with lower common mode range. Likewise, you may require that the probe not
change input capacitance, noise, or common mode range as you change the VOLTS/DIV setting.
These requirements can be met by setting the probe to Manual gain control mode. When set to
Manual mode, the dynamic range of the VOLTS/DIV knob is limited to the scale factors that can be
obtained without changing the AP033 gain or attenuation. Thus in Manual gain control mode, only
the scale factor of the oscilloscope will be changed. In this mode, dedicated menu boxes are
displayed for Probe Attenuation and Probe Gain. (Refer to Figure 3). The available values that
appear in the Probe Atten menu box will change depending on the presence of the external
attenuator. When the external ÷10 attenuator is not installed, ÷10 and ÷1 will be displayed. With
the external ÷10 attenuator, only ÷100 will be displayed. In software versions 8.1.0 and higher, the
channel OFFSET knob will control the probe offset, rather than the offset at the oscilloscope input.
The OFFSET buttons on the probe body are disabled.
The Coupling Menu refers to the probe input. The common mode dynamic range (CMDR) for the
selected probe gain and attenuation settings are displayed in the Probe Attenuation menu In some
versions of software, the input capacitance from each input to ground is also displayed.
When using the AP033 with the ADPPS power supply on oscilloscopes without a ProBus interface,
use Table 2 to select the desired effective volts per division scaling.
922260-00 Rev A
13
相关PDF资料 |
PDF描述 |
|---|---|
| AP034 | PROBE ACT DIFFERENTIAL 1GHZ |
| AP2S2LC | OSCILLATOR PROG 1.8V +-50PPM SMD |
| AP3S1EJ | OSCILLATOR PROG 2.5V +-20PPM SMD |
| APGDT001 | SYSTEM DEV LIN SERIAL ANALYZER |
| ARE0810KS04 | SWITCH DIP SPST EXTENDED 8POS SM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AP033 | 制造商:Lecroy Corporation 功能描述:DIFF. PROBE 500MHZ ((NS)) |
| AP-033/A/N | 制造商:MISCELLANEOUS 功能描述: |
| AP0332 | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
| AP0332CG | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
| AP0332ND | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
发布紧急采购，3分钟左右您将得到回复。