- 您现在的位置：买卖IC网 > Datasheet目录667 > AP033 (Teledyne LeCroy)PROBE DIFFERENTIAL 500MHZ Datasheet资料下载
参数资料
| 型号： | AP033 |
| 厂商： | Teledyne LeCroy |
| 文件页数： | 29/62页 |
| 文件大小： | 0K |
| 描述： | PROBE DIFFERENTIAL 500MHZ |
| 产品培训模块： | Fundamentals of Probing Overview |
| 标准包装： | 1 |
| 系列： | AP |
| 类型： | 有源差分 |
| 衰减值： | 1:1，10:1 |
| 带宽： | 500MHz |
| 电阻 - 输入： | 2M |
| 电压 - 最大： | CAT I 42.4V |
| 电容 - 输入： | 2.7pF，1.2pF |
| 线缆长度： | 42.000"（1066.80mm） |
| 颜色： | 灰 |
| 包括： | AC 耦合器，附件工具包，衰减器，外壳，手册 |
| 配用： | MSO 44MXS-B-ND - DGTL O-SCOPE MIX SGL 400MHZ DSO MSO 64MXS-B-ND - DGTL O-SCOPE MIX SGL 600MHZ DSO MSO 104MXS-B-ND - DGTL O-SCOPE MIX SGL 1GHZ DSO WAVESURFER 104MXS-B-ND - DGTL O-SCOPE 1GHZ 5GS/S 4CH WAVESURFER 64MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 4CH WAVESURFER 62MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 2CH WAVESURFER 44MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 4CH WAVESURFER 42MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 2CH WAVESURFER 24MXS-B-ND - DGTL O-SCOPE 200MHZ 2.5GS/S 4CH |
| 相关产品： | PK033-ND - AP033/AP034 ACCES KIT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
Operator’s Manual
Note: You can fabricate the Adjustment Tool by flattening the end of a 0.025 in. (0.635 mm)
square pin with a file. Insert the pin into a short length of rigid plastic tubing to serve as a handle.
Procedure
1. Attach the AP033 to the test oscilloscope. If the test oscilloscope is not equipped with ProBus,
use the ADPPS to provide power for the AP033.
2. Attach the ? ÷ ??? Attenuator Adapter to the AP033 probe tip.
3. Insert 0.025 in. (0.635 mm) square pins into the + , - , and input connectors of the
????? Attenuator Adapter.
4. Attach the interconnect cable to the output of the signal source.
5. Attach the Trigger Out signal from the signal source to the External Trigger Input of the test
oscilloscope. If the signal source does not have a separate Trigger Out signal, use a BNC Tee
connector in the output. Run one cable to the External Trigger Input of the test oscilloscope.
Connect the other to the probe inputs.
6. Using the alligator clips on the end of the interconnect cable, connect the signal source ground
to the square pin on the ? ÷ ??? Attenuator Adapter’s “ - “ input. Attach the signal output to the
square pin on the ? ÷ ??? Attenuator Adapter’s “ + ” input.
7. Turn on the test oscilloscope. Set the AP033 GAIN to X10. The EFFECTIVE GAIN indicator for
? ÷ ??? should be lit. (NOTE: If the X1 EFFECTIVE GAIN indicator is lit rather than the ? ÷10, make
sure that the adapter installed on the probe tip is the ? ÷ ??? Attenuator, and not the AC
Coupler.)
8. Set the test oscilloscope Volts/Div to 200 mV (for Teledyne LeCroy oscilloscopes with ProBus)
or 20 mV/Div when using the ADPPS with an oscilloscope without scale factor correction; 5
? s/Div; AUTO trigger mode; Trigger source: External. Set the Bandwidth Limiting to 20-30 MHz
and Average the waveform 1:31 to reduce noise.
9. Turn on the signal source. Set the output frequency to approximately 5 kHz. Set the output
amplitude to approximately 1 Volt.
10. Adjust the test oscilloscope trigger level for a stable trace. If necessary, use the probe offset to
position the waveform to show the square corner of the test signal.
NOTE: Do not use the oscilloscope offset or position controls to reposition the trace. Many of
the signal generators used for compensation calibration only have square corners on one of the
two edges of the output waveform. (Rising or falling edge, but not both.) Be sure to display the
correct edge for this step.
922260-00 Rev A
23
相关PDF资料 |
PDF描述 |
|---|---|
| AP034 | PROBE ACT DIFFERENTIAL 1GHZ |
| AP2S2LC | OSCILLATOR PROG 1.8V +-50PPM SMD |
| AP3S1EJ | OSCILLATOR PROG 2.5V +-20PPM SMD |
| APGDT001 | SYSTEM DEV LIN SERIAL ANALYZER |
| ARE0810KS04 | SWITCH DIP SPST EXTENDED 8POS SM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AP033 | 制造商:Lecroy Corporation 功能描述:DIFF. PROBE 500MHZ ((NS)) |
| AP-033/A/N | 制造商:MISCELLANEOUS 功能描述: |
| AP0332 | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
| AP0332CG | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
| AP0332ND | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
发布紧急采购，3分钟左右您将得到回复。