- 您现在的位置：买卖IC网 > Datasheet目录667 > AP033 (Teledyne LeCroy)PROBE DIFFERENTIAL 500MHZ Datasheet资料下载
参数资料
| 型号： | AP033 |
| 厂商： | Teledyne LeCroy |
| 文件页数： | 36/62页 |
| 文件大小： | 0K |
| 描述： | PROBE DIFFERENTIAL 500MHZ |
| 产品培训模块： | Fundamentals of Probing Overview |
| 标准包装： | 1 |
| 系列： | AP |
| 类型： | 有源差分 |
| 衰减值： | 1:1，10:1 |
| 带宽： | 500MHz |
| 电阻 - 输入： | 2M |
| 电压 - 最大： | CAT I 42.4V |
| 电容 - 输入： | 2.7pF，1.2pF |
| 线缆长度： | 42.000"（1066.80mm） |
| 颜色： | 灰 |
| 包括： | AC 耦合器，附件工具包，衰减器，外壳，手册 |
| 配用： | MSO 44MXS-B-ND - DGTL O-SCOPE MIX SGL 400MHZ DSO MSO 64MXS-B-ND - DGTL O-SCOPE MIX SGL 600MHZ DSO MSO 104MXS-B-ND - DGTL O-SCOPE MIX SGL 1GHZ DSO WAVESURFER 104MXS-B-ND - DGTL O-SCOPE 1GHZ 5GS/S 4CH WAVESURFER 64MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 4CH WAVESURFER 62MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 2CH WAVESURFER 44MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 4CH WAVESURFER 42MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 2CH WAVESURFER 24MXS-B-ND - DGTL O-SCOPE 200MHZ 2.5GS/S 4CH |
| 相关产品： | PK033-ND - AP033/AP034 ACCES KIT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
AP033 Active Differential Probe
2. Carefully move the AP033 probe head from the Differential Drive No Termination connector of
the AP033/AP034 Calibration Fixture to the Differential Drive 50 Ohm Termination connector.
Make sure that the probe is fully engaged in the fixture.
3. Set the oscilloscope to display channel 1.Set Coupling to DC 1 M ? , and Global BWL to Off.
Autobalance the AP033 by pressing the AUTOBALANCE button twice. Set the oscilloscope
trigger mode to AUTO.
4. If necessary, center the trace with the Probe Offset (or Channel O FFSET ) knob.
5. Connect the output of the leveled sine wave generator to the Differential Drive 50 Ohm
Termination connector of the AP033/AP034 Calibration Fixture. If using a model SG504
generator, insert a ÷2 50Ω BNC attenuator between the generator output and the test fixture
input.
6. Set the leveled sine wave generator frequency to 50 kHz, and the amplitude to approximately
300 mVp-p. When using a model SG504 generator, set the output to 0.6V pk-pk at the output
which will correspond to 300 mV at the output of the ÷2 attenuator.
7. Set the oscilloscope vertical scale factor to 50 mV/div and the horizontal scale factor to 10
μsec/div. Set the Trigger source to Channel 1. Adjust the trigger level for a stable display. Turn
on Math Channel A. Press MATH SETUP, then REDEFINE A. Set the A Math type to Average, Avg
Type to Continuous, with 1:15 weighting, of channel 1. Turn off the trace 1 display.
8. Adjust the output amplitude of the leveled sine wave generator for a display of exactly 6
divisions (300 mV) peak to peak.
9. Change the leveled sine wave generator frequency to 250 MHz, taking care not to change the
output amplitude.
10. Change the oscilloscope horizontal scale to 1 ns/div. In the SETUP TIMEBASE menu, select RIS
Sampling. If necessary, turn the channel 1 display back on and adjust the trigger for a stable
trace. Once a stable trace has been achieved, turn off the channel 1 trace to only display the
averaged waveform.
11. Measure the peak-to-peak output amplitude of the AP033. Record the reading to two-digit
resolution (xx0 mV) as ‘Probe Output Voltage at 250 MHz’ in the Test Record.
12. Divide the measured output amplitude recorded in step B-11 by 300 mV. Record the answer to
two- digit resolution (0.xx) in the Test Record. This is the ‘Differential Mode Gain at 250 MHz’.
13. Move the leveled sine wave generator output cable from the Differential Drive 50 Ohm
Termination connector of the AP033/AP034 Calibration Fixture to the channel 2 input of the
oscilloscope.
30
922260-00 Rev A
相关PDF资料 |
PDF描述 |
|---|---|
| AP034 | PROBE ACT DIFFERENTIAL 1GHZ |
| AP2S2LC | OSCILLATOR PROG 1.8V +-50PPM SMD |
| AP3S1EJ | OSCILLATOR PROG 2.5V +-20PPM SMD |
| APGDT001 | SYSTEM DEV LIN SERIAL ANALYZER |
| ARE0810KS04 | SWITCH DIP SPST EXTENDED 8POS SM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AP033 | 制造商:Lecroy Corporation 功能描述:DIFF. PROBE 500MHZ ((NS)) |
| AP-033/A/N | 制造商:MISCELLANEOUS 功能描述: |
| AP0332 | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
| AP0332CG | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
| AP0332ND | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
发布紧急采购，3分钟左右您将得到回复。