- 您现在的位置：买卖IC网 > Datasheet目录667 > AP033 (Teledyne LeCroy)PROBE DIFFERENTIAL 500MHZ Datasheet资料下载
参数资料
| 型号： | AP033 |
| 厂商： | Teledyne LeCroy |
| 文件页数： | 44/62页 |
| 文件大小： | 0K |
| 描述： | PROBE DIFFERENTIAL 500MHZ |
| 产品培训模块： | Fundamentals of Probing Overview |
| 标准包装： | 1 |
| 系列： | AP |
| 类型： | 有源差分 |
| 衰减值： | 1:1，10:1 |
| 带宽： | 500MHz |
| 电阻 - 输入： | 2M |
| 电压 - 最大： | CAT I 42.4V |
| 电容 - 输入： | 2.7pF，1.2pF |
| 线缆长度： | 42.000"（1066.80mm） |
| 颜色： | 灰 |
| 包括： | AC 耦合器，附件工具包，衰减器，外壳，手册 |
| 配用： | MSO 44MXS-B-ND - DGTL O-SCOPE MIX SGL 400MHZ DSO MSO 64MXS-B-ND - DGTL O-SCOPE MIX SGL 600MHZ DSO MSO 104MXS-B-ND - DGTL O-SCOPE MIX SGL 1GHZ DSO WAVESURFER 104MXS-B-ND - DGTL O-SCOPE 1GHZ 5GS/S 4CH WAVESURFER 64MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 4CH WAVESURFER 62MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 2CH WAVESURFER 44MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 4CH WAVESURFER 42MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 2CH WAVESURFER 24MXS-B-ND - DGTL O-SCOPE 200MHZ 2.5GS/S 4CH |
| 相关产品： | PK033-ND - AP033/AP034 ACCES KIT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
AP033 Active Differential Probe
Preliminary Procedure
1. Using pliers, carefully remove each of the push buttons from the ProBus interface housing by
gently pulling them away from the housing.
2. Remove the two screws that secure the plastic cover on the cable end of the ProBus interface
housing. Gently pull on the probe cable to slide the circuit board assembly from the metal
housing.
3. Remove the 5/64 in. (2 mm) Allen head cap screw from the small cover on the back of the
probe tip. Remove the cover along with the small cover on the opposite side of the probe. Hold
the shielded portion of the probe head in one hand and gently slide the larger cover off by
pulling it away from the probe tip end.
4. Connect the AP033 Active Differential Probe output to the female end of the ProBus Extension
Cable. Be careful to align the ProBus pins with the corresponding connector correctly. Connect
the male end of the ProBus Extension Cable to Channel 1 of the oscilloscope.
NOTE: The Logic board is connected to the Amplifier board by four small 8-pin connectors.
There are no additional mechanical fasteners holding the two boards together. A small foam
pad mounted on the circuit board ensures that the connectors remain engaged while the
assembly is mounted within the ProBus interface housing. Be sure that the connectors
between the boards are firmly engaged before applying power to the probe. Operating the
probe without the logic board will not damage it. However, to ensure reliable operation, the
logic board should only be mated with the Amplifier board with the power removed, and the
ProBus connector disengaged.
5. Apply power to the oscilloscope and to the other test instrumentation. Allow at least 30
minute’s warm -up time for the AP033 Active Differential Probe and test equipment before
continuing the calibration procedure.
NOTE: The probe tip cover also serves to thermally stabilize the input circuitry. The differential
input stage of the probe utilizes discrete transistors that need to maintain an approximate
match of junction temperatures for correct DC balance. With the covers removed, this circuitry
is susceptible to drift caused by air currents flowing over the components. Remove or redirect
any fans that may be blowing air currents over the probe tip during adjustment.
Correct operation of the AP033 Active Differential Probe controls requires software version
8.1.0 or higher. You can find out the software version loaded on your Teledyne LeCroy scope by
pressing SHOW STATUS, then selecting the System menu option. In version 8.1.0 and higher,
the OFFSET controls on the probe are disabled. Offset is controlled by the OFFSET knob in the
oscilloscope CHANNEL section.
38
922260-00 Rev A
相关PDF资料 |
PDF描述 |
|---|---|
| AP034 | PROBE ACT DIFFERENTIAL 1GHZ |
| AP2S2LC | OSCILLATOR PROG 1.8V +-50PPM SMD |
| AP3S1EJ | OSCILLATOR PROG 2.5V +-20PPM SMD |
| APGDT001 | SYSTEM DEV LIN SERIAL ANALYZER |
| ARE0810KS04 | SWITCH DIP SPST EXTENDED 8POS SM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AP033 | 制造商:Lecroy Corporation 功能描述:DIFF. PROBE 500MHZ ((NS)) |
| AP-033/A/N | 制造商:MISCELLANEOUS 功能描述: |
| AP0332 | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
| AP0332CG | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
| AP0332ND | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:8 P-Channel Latchable Power MOSFET Array |
发布紧急采购，3分钟左右您将得到回复。