参数资料
型号: C8051F300-TB
厂商: Silicon Laboratories Inc
文件页数: 109/178页
文件大小: 0K
描述: BOARD PROTOTYPING W/C8051F300
标准包装: 1
类型: MCU
适用于相关产品: C8051F300
所含物品:
C8051F300/1/2/3/4/5
36
Rev. 2.9
5.1.
Analog Multiplexer and PGA
The analog multiplexers (AMUX0) select the positive and negative inputs to the PGA, allowing any Port pin
to be measured relative to any other Port pin or GND. Additionally, the on-chip temperature sensor or the
positive power supply (VDD) may be selected as the positive PGA input. When GND is selected as the
negative input, ADC0 operates in Single-ended Mode; all other times, ADC0 operates in Differential
Mode. The ADC0 input channels are selected in the AMX0SL register as described in SFR Definition 5.1.
The conversion code format differs in Single-ended versus Differential modes, as shown below. When in
Single-ended Mode (negative input is selected GND), conversion codes are represented as 8-bit unsigned
integers. Inputs are measured from ‘0’ to VREF x 255/256. Example codes are shown below.
Input Voltage
ADC0 Output (Conversion Code)
VREF x 255/256
0xFF
VREF x 128/256
0x80
VREF x 64/256
0x40
0
0x00
When in Differential Mode (negative input is not selected as GND), conversion codes are represented as
8-bit signed 2s complement numbers. Inputs are measured from –VREF to VREF x 127/128. Example
codes are shown below.
Input Voltage
ADC0 Output (Conversion Code)
VREF x 127/128
0x7F
VREF x 64/128
0x40
0
0x00
–VREF x 64/128
0xC0
–VREF
0x80
Important Note About ADC0 Input Configuration: Port pins selected as ADC0 inputs should be config-
ured as analog inputs and should be skipped by the Digital Crossbar. To configure a Port pin for analog
input, set to ‘0’ the corresponding bit in register P0MDIN. To force the Crossbar to skip a Port pin, set to ‘1’
the corresponding bit in register XBR0. See Section “12. Port Input/Output” on page 103 for more Port
I/O configuration details.
The PGA amplifies the AMUX0 output signal as defined by the AMP0GN1-0 bits in the ADC0 Configuration
register (SFR Definition 5.2). The PGA is software-programmable for gains of 0.5, 1, 2, or 4. The gain
defaults to 0.5 on reset.
5.2.
Temperature Sensor
The typical temperature sensor transfer function is shown in Figure 5.2. The output voltage (VTEMP) is the
positive PGA input when the temperature sensor is selected by bits AMX0P2-0 in register AMX0SL; this
voltage will be amplified by the PGA according to the user-programmed PGA settings.
相关PDF资料
PDF描述
0210391037 CABLE JUMPER 1MM .102M 33POS
C8051F226-TB BOARD PROTOTYPING W/C8051F226
C8051F330-TB BOARD PROTOTYPING W/C8051F330
LGU2G101MELA CAP ALUM 100UF 400V 20% SNAP
SDR-Q SCOTCH CODE REFILL Q
相关代理商/技术参数
参数描述
C8051F300-TB-K 功能描述:BOARD PROTOTYPING W/C8051F300 制造商:silicon labs 系列:- 零件状态:在售 板类型:评估平台 类型:MCU 8-位 核心处理器:8051 操作系统:- 平台:- 配套使用产品/相关产品:C8051F30x 安装类型:固定 内容:板 标准包装:1
C8051F301 功能描述:8位微控制器 -MCU 8KB 2%osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F301-GM 功能描述:8位微控制器 -MCU 8KB 11P MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F301-GMR 功能描述:8位微控制器 -MCU 8KB 11P MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F301-GS 功能描述:8位微控制器 -MCU 8KB Flash 2%osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT