收藏本站
参数资料
型号： C8051F300-TB
厂商： Silicon Laboratories Inc
文件页数： 162/178页
文件大小： 0K
描述： BOARD PROTOTYPING W/C8051F300
标准包装： 1
类型： MCU
适用于相关产品： C8051F300
所含物品： 板
C8051F300/1/2/3/4/5
84
Rev. 2.9
9.1.
Power-On Reset
During powerup, the device is held in a reset state and the RST pin is driven low until VDD settles above
VRST. An additional delay occurs before the device is released from reset; the delay decreases as the VDD
ramp time increases (VDD ramp time is defined as how fast VDD ramps from 0 V to VRST). For valid ramp
times (less than 1 ms), the power-on reset delay (TPORDelay) is typically less than 0.3 ms.
Note: The maximum VDD ramp time is 1 ms; slower ramp times may cause the device to be
released from reset before VDD reaches the VRST level.
On exit from a power-on reset, the PORSF flag (RSTSRC.1) is set by hardware to logic 1. When PORSF is
set, all of the other reset flags in the RSTSRC Register are indeterminate (PORSF is cleared by all other
resets). Since all resets cause program execution to begin at the same location (0x0000) software can
read the PORSF flag to determine if a powerup was the cause of reset. The content of internal data mem-
ory should be assumed to be undefined after a power-on reset. The VDD monitor is disabled following a
power-on reset.
Power-On
Reset
VDD
Monitor
Reset
/RST
t
volt
s
1.0
2.0
Logic HIGH
Logic LOW
T
PORDelay
V
D
2.70
2.55
V
RST
VDD
Figure 9.2. Power-On and VDD Monitor Reset Timing
9.2.
Power-Fail Reset/VDD Monitor
When a power-down transition or power irregularity causes VDD to drop below VRST, the power supply
monitor will drive the RST pin low and hold the CIP-51 in a reset state (see Figure 9.2). When VDD returns
to a level above VRST, the CIP-51 will be released from the reset state. Note that even though internal data
memory contents are not altered by the power-fail reset, it is impossible to determine if VDD dropped below
the level required for data retention. If the PORSF flag reads ‘1’, the data may no longer be valid. The VDD
monitor is disabled after power-on resets; however its defined state (enabled/disabled) is not altered by
any other reset source. For example, if the VDD monitor is enabled and a software reset is performed, the
VDD monitor will still be enabled after the reset. The VDD monitor is enabled by writing a ‘1’ to the PORSF
相关PDF资料
PDF描述
0210391037 CABLE JUMPER 1MM .102M 33POS
C8051F226-TB BOARD PROTOTYPING W/C8051F226
C8051F330-TB BOARD PROTOTYPING W/C8051F330
LGU2G101MELA CAP ALUM 100UF 400V 20% SNAP
SDR-Q SCOTCH CODE REFILL Q
相关代理商/技术参数
参数描述
C8051F300-TB-K 功能描述:BOARD PROTOTYPING W/C8051F300 制造商:silicon labs 系列:- 零件状态:在售 板类型:评估平台 类型:MCU 8-位 核心处理器:8051 操作系统:- 平台:- 配套使用产品/相关产品:C8051F30x 安装类型:固定 内容:板 标准包装:1
C8051F301 功能描述:8位微控制器 -MCU 8KB 2%osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F301-GM 功能描述:8位微控制器 -MCU 8KB 11P MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F301-GMR 功能描述:8位微控制器 -MCU 8KB 11P MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F301-GS 功能描述:8位微控制器 -MCU 8KB Flash 2%osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*