参数资料
| 型号： | CDB5460AU |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 33/54页 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD FOR CS5460A |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电度表/功率表 |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | CS5460A |
| 主要属性： | 1 相电流和电压监控 |
| 次要属性： | 图形用户接口，SPI? 和 USB 接口 |
| 已供物品： | 板，线缆，软件 |
| 相关产品： | CS5460A-BSZR-ND - IC ENERGY METERING 1PHASE 24SSOP 598-1701-ND - IC PWR/ENERGY 1PH BIDIR 24SSOP 598-1700-ND - IC PWR/ENERGY 1PH BIDIR 24SSOP 598-1094-5-ND - IC ENERGY METERING 1PHASE 24SSOP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
CS5460A
The voltage/current-channel inputs have
surge-current limits of 100 mA. This applies to brief
voltage/current spikes (<250 ms). The limit is
10 mA for DC input overload situations. To prevent
permanent damage to the CS5460A, the designer
must include adequate protection circuitry in the
power meter design, to insure that these pin cur-
rent limits are never exceeded, when CS5460A is
operating in the intended power-line metering envi-
ronment.
Focusing specifically on Figure 7, which shows
how voltage/current transformers can be used to
sense the line-voltage/line-current, suppose for ex-
ample that the requirements for a certain 120 VAC
power system require that the power meter must
be able to withstand up to a 8 kV voltage spike on
the power line during normal operating conditions.
To provide a suitable sensor voltage input level to
the voltage channel input pins of the CS5460A, the
turns ratio of the voltage-sense transformer should
be chosen such that the ratio is, for example, on
the order of 1000:1. A voltage-sense transformer
with a 1000:1 turns ratio will provide a 120 mV
(rms) signal to the CS5460A’s differential voltage
channel inputs, when the power line voltage is at
the nominal level of 120 VAC. Therefore, a brief
8 kV surge would be reduced to a 8 V surge across
R V+ .
What happens when 8 volts (common-mode) is
present across one of the analog input pins of the
CS5460A? The Vin+/Vin- and Iin+/Iin- pins of the
CS5460A are equipped with internal protection di-
odes. If a voltage is presented to any of these pins
that is larger than approximately 7 V (with respect
to VA- pin) these protection diodes will turn on in-
side the CS5460A. But in order to prevent exces-
sive current levels from flowing through the device,
the value of R V+ must be large enough that when a
8V surge is present across the secondaries of the
voltage-sense transformer, the brief surge current
through R V+ should not be any greater than
100 mA. Therefore, a minimum value for R V+
would be (8 V - 7 V) / 100 mA = 10 ? . This value
may be increased as needed, to easily obtain the
desired cutoff frequency of the anti-aliasing filter on
the voltage channel (described later), and also to
provide some margin. But the designer should try
DS487F5
to avoid using values for the protection resistors
that are excessively high. A typical value for R V+
would be 470 ? .
The VIN- pin should also have a protection resistor
(called R V- in Figure 7). To maintain symmetry, the
value of R V- should be made equal to R V+ .
For the current channel inputs (Iin+ and Iin-), if the
maximum current rating (I max ) for this power line is
30 A (RMS), then a suitable turns ratio for the cur-
rent-sense transformer might be 200:1. Since the
maximum load for a 120 VAC line rated at 30 A
would be 4 ? (for unity power factor), a brief 8 kV
surge across “L” and “N” could generate as much
as 2000 A (RMS) of current through the primaries
of the current-sense transformer. This can in turn
generate as much as 10 V across the secondaries
of the current-sense transformer. This voltage is
high enough to turn on one or more of the internal
protection diodes located off of the Iin+/Iin- pins.
Therefore, the value of the protection resistor that
will limit the current flow to less than 100 mA would
be (10 V - 7 V) / 100 mA = 30 ? . In order to pro-
vide some margin and to use the same resistor val-
ues that are used on the Vin+/Vin- pins, a 470 ?
resistor can be used as a lower limit for the R I+ and
R I- resistors shown in Figure 7.
Referring to the circuit implementations shown in
Figures 6, 8, and 9, note that when resistor-divider
configurations are used to provide the voltage
channel sense voltage, the VIN+ pin does not need
an additional, separate, dedicated protection resis-
tor. This is because the resistive voltage-divider al-
ready provides the series resistance that is needed
for this protection resistance (from R 1 and R 2 ).
(And note in Figure 8 that this is true for both the
VIN+ pin and the VIN- pin.) In Figure 7, a voltage
transformer is used as the voltage sensor. When
any type of transformer is used as the sensor de-
vice for voltage (or current) channel, a dedicated
protection resistor R V+ should be installed in series
with the VIN+ pin, and similarly, a resistor (R V- )
should be installed in series to the VIN- input pin.
Additional considerations/techniques regarding
the protection of the analog input pins against sud-
den high-frequency, high-level voltage/current
surges are discussed in Section 3.14.
33
相关PDF资料 |
PDF描述 |
|---|---|
| CDB5461AU | BOARD EVAL & SOFTWARE CS5461A |
| CDB5466U | BOARD EVAL & SOFTWARE CS5466 ADC |
| CDB5467U | BOARD EVAL FOR CS5467 ADC |
| CDB5560-2 | DEV BOARD FOR CS5560 W/SE INPUT |
| CDB5571-2 | DEV BOARD FOR CS5571 W/SE INPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CDB5460AU-Z | 制造商:Cirrus Logic 功能描述:PB-FREEEVAL BOARD FOR CS5460 - Bulk |
| CDB5461 | 制造商:Cirrus Logic 功能描述:EVAL BD FOR CS5461 - Bulk |
| CDB5461A | 功能描述:EVAL BOARD FOR CS5461 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
| CDB5461AU | 功能描述:数据转换 IC 开发工具 Eval Bd Sngl-Phase Pow/Energy RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| CDB5461AU-Z | 制造商:Cirrus Logic 功能描述:PB-FREEEVAL BOARD FOR CS5461 WITH USB - Bulk |
发布紧急采购，3分钟左右您将得到回复。