参数资料
| 型号： | DS1873T+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 23/86页 |
| 文件大小： | 0K |
| 描述： | IC CTLR SFP+ ANLG LDD 28-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 类型： | 激光二极管控制器 |
| 通道数： | 1 |
| 电源电压： | 2.85 V ~ 3.9 V |
| 电流 - 电源： | 2.5mA |
| 工作温度： | -40°C ~ 95°C |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 托盘 |
| 安装类型： | 表面贴装 |
| 其它名称： | 90-1873T+000 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页
SFP+ Controller with Analog LDD Interface
DETECTION OF TXF FAULT
TXF
Figure 15a. TXF Nonlatched Operation
DETECTION OF TXF FAULT
TXD OR TXF RESET
TXF
Figure 15b. TXF Latched Operation
Transmit Fault (TXF) Output
TXF can be triggered by all alarms, warnings, and
quick trips (Figure 13). The six ADC alarms, warnings,
and the LOS quick trips require enabling (Table
01h/05h, Registers F8h and FDh). See Figures 15a and
15b for nonlatched and latched operation. Latching of
the alarms is controlled by the CNFGB and CNFGC
registers (Table 02h, Registers 8Ah–8Bh).
Die Identification
The DS1873 has an ID hardcoded in its die. Two regis-
ters (Table 02h, Registers CEh–CFh) are assigned for
this feature. The CEh register reads 73h to identify the
part as the DS1873, while the CFh register reads the
current device version.
I2C Communication
I 2 C Definitions
The following terminology is commonly used to
describe I 2 C data transfers.
Master device: The master device controls the
slave devices on the bus. The master device gen-
erates SCL clock pulses and START and STOP
conditions.
Slave devices: Slave devices send and receive
data at the master’s request.
Bus idle or not busy: Time between STOP and
START conditions when both SDA and SCL are inac-
tive and in their logic-high states.
START condition: A START condition is generated
by the master to initiate a new data transfer with a
slave. Transitioning SDA from high to low while SCL
remains high generates a START condition. See
Figure 16 for applicable timing.
STOP condition: A STOP condition is generated by
the master to end a data transfer with a slave.
Transitioning SDA from low to high while SCL
remains high generates a STOP condition. See
Figure 16 for applicable timing.
Repeated START condition: The master can use a
repeated START condition at the end of one data
transfer to indicate that it will immediately initiate a
new data transfer following the current one.
Repeated STARTs are commonly used during read
operations to identify a specific memory address to
begin a data transfer. A repeated START condition
is issued identically to a normal START condition.
See Figure 16 for applicable timing.
______________________________________________________________________________________
23
相关PDF资料 |
PDF描述 |
|---|---|
| DS1874T+ | IC CTLR SFP+ ANLG LDD 28-TQFN |
| DS2129S+T&R | IC REGULATOR SCSI 16-SOIC |
| DS2438Z+T&R | IC MONITOR SMART BATTERY 8-SOIC |
| DS2703U+ | IC BATT AUTHENTICATE SHA-1 8UMAX |
| DS2705U+ | IC AUTHENTICATE SHA-1 8-UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1873T+ | 功能描述:ADC / DAC多通道 SFP+ Ctrl w/Analog RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS1873T+T&R | 制造商:Maxim Integrated Products 功能描述:5X5 TQFN SFP+ CTRL W/ANALOG - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CTLR SFP+ ANLG LDD 28-TQFN |
| DS1873T+T&R | 功能描述:ADC / DAC多通道 SFP+ Ctrl w/Analog RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS1873T+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:SFP+ Controller with Analog LDD Interface |
| DS1874 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:SFP+ Controller with Digital LDD Interface |
发布紧急采购，3分钟左右您将得到回复。