收藏本站
参数资料
型号： DS3120N
厂商： Maxim Integrated Products
文件页数： 81/133页
文件大小： 0K
描述： IC FRAMER T1 28-CHANNEL IND
标准包装： 1
控制器类型： T1 调帧器
接口： 并行/串行
电源电压： 2.97 V ~ 3.63 V
电流 - 电源： 300mA
工作温度： -40°C ~ 85°C
安装类型： 表面贴装
封装/外壳： 316-BGA
包装： 管件
DS3112
51 of 133
Register Name:
T3E3EIC
Register Description:
T3/E3 Error Insert Control Register
Register Address:
18h
Bit #
7
6
5
4
3
2
1
0
Name
MEIMS
FBEIC1
FBEIC0
FBEI
T3CPBEI
T3PBEI
EXZI
BPVI
Default
0
Bit #
15
14
13
12
11
10
9
8
Name
—
Default
—
Bit 0: BiPolar Violation Insert (BPVI). A zero to one transition on this bit will cause a single BPV to be inserted
into the transmit data stream. Once this bit has been toggled from a 0 to a 1, the device waits for the next
occurrence of three consecutive ones to insert the BPV. This bit must be cleared and set again for a subsequent
error to be inserted. Toggling this bit has no affect when the T3/E3 interface is in the Unipolar Mode (Section 4.2
for details about the Unipolar Mode). In the manual error insert mode (MEIMS = 1), errors will be inserted on each
toggle of the FTMEI input signal as long as this bit is set high. When this bit is set low, no errors will be inserted.
Bit 1: Excessive Zero Insert (EXZI). A zero to one transition on this bit will cause a single EXZ event to be
inserted into the transmit data stream. An EXZ event is defined as three or more consecutive zeros in the T3 mode
and four or more consecutive zeros in the E3 mode. Once this bit has been toggled from a zero to a one, the device
waits for the next possible B3ZS/HDB3 codeword insertion and it suppresses that codeword from being inserted
and hence this creates the EXZ event. This bit must be cleared and set again for a subsequent error to be inserted.
Toggling this bit has no affect when the T3/E3 interface is in the Unipolar Mode (Section 4.2 for details about the
Unipolar Mode). In the Manual Error Insert mode (MEIMS = 1), errors will be inserted on each toggle of the
FTMEI input signal as long as this bit is set high. When this bit is set low, no errors will be inserted.
Bit 2: T3 Parity Bit Error Insert (T3PBEI). A zero to one transition on this bit will cause a single T3 parity error
event to be inserted into the transmit data stream. A T3 parity event is defined as flipping the proper polarity of
both the P bits in a T3 Frame. (See Section 14.5 for details about the P bits.) Once this bit has been toggled from a
zero to a one, the device waits for the next T3 frame to flip both P bits. This bit must be cleared and set again for a
subsequent error to be inserted. Toggling this bit has no affect when the device is operated in the E3 mode. In the
Manual Error Insert mode (MEIMS = 1), errors will be inserted on each toggle of the FTMEI input signal as long
as this bit is set high. When this bit is set low, no errors will be inserted.
Bit 3: T3 C-Bit Parity Error Insert (T3CPBEI). A zero to one transition on this bit will cause a single T3 C-Bit
parity error event to be inserted into the transmit data stream. A T3 parity event is defined as flipping the proper
polarity of all three CP bits in a T3 Frame. (See Section 14.7 for details about the CP bits.) Once this bit has been
toggled from a zero to a one, the device waits for the next T3 frame to flip the three CP bits. This bit must be
cleared and set again for a subsequent error to be inserted. Toggling this bit has no affect when the T3 framer is not
operated in the C-Bit parity mode (See Section 14.7 for details about the C-Bit Parity mode.) or when the device is
operated in the E3 mode. In the Manual Error Insert mode (MEIMS = 1), errors will be inserted on each toggle of
the FTMEI input signal as long as this bit is set high. When this bit is set low, no errors will be inserted.
Bit 4: Frame Bit Error Insert (FBEI). A zero to one transition on this bit will cause the transmit framer to
generate framing bit errors. The type of framing bit errors inserted is controlled by the FBEIC0 and FBEIC1 bits
(see discussion below). Once this bit has been toggled from a 0 to a 1, the device waits for the next possible
framing bit to insert the errors. This bit must be cleared and set again for a subsequent error to be inserted. In the
Manual Error Insert mode (MEIMS = 1), errors will be inserted on each toggle of the FTMEI input signal as long
as this bit is set high. When this bit is set low, no errors will be inserted.
相关PDF资料
PDF描述
DS31256+ IC CTRLR HDLC 256-CHANNEL 256BGA
DS3141+ IC FRAMER DS3/E3 SNGL 144CSBGA
DS31412N IC 12CH DS3/3 FRAMER 349-BGA
DS3150TN IC LIU T3/E3/STS-1 IND 48-TQFP
DS3154N+ IC LIU DS3/E3/STS-1 QD 144CSBGA
相关代理商/技术参数
参数描述
DS3121 功能描述:IC TGATOR T1-T3 AGGREGATOR RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A
DS3121N 功能描述:IC TGATOR T1-T3 AGGREGATOR IND RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A
DS31256 功能描述:输入/输出控制器接口集成电路 256Ch High Thruput HDLC Cntlr RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray
DS31256+ 功能描述:输入/输出控制器接口集成电路 256Ch High Thruput HDLC Cntlr RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray
DS31256B 功能描述:输入/输出控制器接口集成电路 256Ch High Thruput HDLC Cntlr RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*