- 您现在的位置：买卖IC网 > PDF目录18722 > EM250-RCM-R (Silicon Laboratories Inc)EM250 RCM BOARD PDF资料下载
参数资料
| 型号： | EM250-RCM-R |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 44/124页 |
| 文件大小： | 0K |
| 描述： | EM250 RCM BOARD |
| 标准包装： | 12 |
| 类型： | 收发器，802.15.4/Zigbee |
| 频率： | 2.4GHz |
| 适用于相关产品： | EM250 |
| 其它名称： | 636-1023 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页
EM250
further reception is dropped and the register bit SC_SPIRXOVF in the SC1_SPISTAT register is set. The RX
FIFO hardware generates the INT_SCRXOVF interrupt, but the DMA register will not indicate the error
condition until the RX FIFO is drained. Once the DMA marks a RX error, there are two conditions that will clear
the error indication: setting the appropriate SC_TX/RXDMARST bit in the SC1_DMACTRL register, or loading the
appropriate DMA buffer after it has unloaded.
Receiving a character always requires transmitting a character. In a case when a long stream of receive
characters is expected, a long sequence of (dummy) transmit characters must be generated. To avoid
software or transmit DMA initiating these transfers (and consuming unnecessary bandwidth), the SPI serializer
can be instructed to retransmit the last transmitted character, or to transmit a busy token ( 0xFF ), which is
determined by the register bit SC_SPIRPT in the SC1_SPICFG register. This functionality can only be enabled
(or disabled) when the transmit FIFO is empty and the transmit serializer is idle, as indicated by a cleared
SC_SPITXIDLE register bit in the SC1_SPISTAT register.
Every time an automatic character transmission is started, a transmit underrun is detected (as there is no data
in transmit FIFO), and the register bit INT_SCTXUND in the INT_SC1FLAG register is set. Note that after
disabling the automatic character transmission, the reception of new characters stops and the receive FIFO
holds characters just received.
Note:
The event Receive DMA complete does not automatically mean receive FIFO empty.
Interrupts are generated on the following events:
?
?
?
?
?
?
?
Transmit FIFO empty and last character shifted out (0 to 1 transition of SC_SPITXIDLE )
Transmit FIFO changed from full to not full (0 to 1 transition of SC_SPITXFREE )
Receive FIFO changed from empty to not empty (0 to 1 transition of SC_SPIRXVAL )
Transmit DMA buffer A/B complete (1 to 0 transition of SC_TXACTA/B )
Receive DMA buffer A/B complete (1 to 0 transition of SC_RXACTA/B )
Received and lost character while receive FIFO was full (Receive overrun error)
Transmitted character while transmit FIFO was empty (Transmit underrun error)
To generate interrupts to the CPU, the interrupt masks in the INT_SC1CFG and INT_CFG registers must be
enabled.
5.2.3
I 2 C Master Mode
The SC1 I 2 C controller is only available in master mode. The SC1 I 2 C controller is enabled with SC1_MODE set to
3. The I 2 C Master controller supports Standard (100kbps) and Fast (400kbps) I 2 C modes. Address arbitration is
not implemented, so multiple master applications are not supported. The I 2 C signals are pure open-collector
signals, and external pull-up resistors are required.
The SC1 I 2 C mode has the following features:
?
?
Programmable clock frequency (400kHz max.)
Supports both 7-bit and 10-bit addressing
The following signals can be made available on the GPIO pins:
?
?
MSDA (serial data)
MSCL (serial clock)
The I 2 C Master controller obtains its reference clock from a programmable clock generator. Clock rates are set
by a clock division ratio from the 24MHz clock:
Nominal Rate = 24MHz / ( 2 * (LIN + 1) * 2 EXP )
120-0082-000V Rev 1.1
Page 44
相关PDF资料 |
PDF描述 |
|---|---|
| EK42552-02 | BOARD EVAL FOR 42552 REV 02 |
| TC25V3A32K7680 | OSCILLATOR 32.7680 KHZ 1.5V SMD |
| 7020-01040-0 | TRANSFORMER CURRENT 200A |
| SI1000DK | DEVELOPMENT KIT SI101X |
| 7020-01038-0 | TRANSFORMER CURRENT 100A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EM250-RTR | 功能描述:IC ZIGBEE SYSTEM-ON-CHIP 48-QFN RoHS:是 类别:RF/IF 和 RFID >> RF 收发器 系列:EM250 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:30 系列:- 频率:4.9GHz ~ 5.9GHz 数据传输率 - 最大:54Mbps 调制或协议:* 应用:* 功率 - 输出:-3dBm 灵敏度:- 电源电压:2.7 V ~ 3.6 V 电流 - 接收:* 电流 - 传输:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 工作温度:-25°C ~ 85°C 封装/外壳:68-TQFN 裸露焊盘 包装:管件 |
| EM250-STACK-R | 制造商:Silicon Laboratories Inc 功能描述:EM250 BOARD STACK (RCM + BREAKOUT) - Boxed Product (Development Kits) 制造商:Silicon Laboratories Inc 功能描述:BOARD STACK EM250 RCM & BREAKOUT |
| EM25-12V-DC | 制造商:ECLIPSE MAGNETICS 功能描述:HOLDING ELECTRO MAGNET |
| EM2513N/11560 | 制造商:ebm-papst Inc 功能描述:- Bulk |
| EM2524N/11560 | 制造商:ebm-papst Inc 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。