- 您现在的位置：买卖IC网 > Datasheet目录411 > EM260-BBRD-128K-USART-R (Silicon Laboratories Inc)EM260 BREAKOUT BOARD Datasheet资料下载
参数资料
| 型号： | EM260-BBRD-128K-USART-R |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 28/50页 |
| 文件大小： | 0K |
| 描述： | EM260 BREAKOUT BOARD |
| 标准包装： | 12 |
| 类型： | 收发器，802.15.4/Zigbee |
| 频率： | 2.4GHz |
| 适用于相关产品： | EM260 |
| 其它名称： | 636-1026 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
EM260
will be 0x82 , since the version number corresponding to this set of Command-Response values is version
number 2. The version number can be a value from 1 to 63 ( 0x81–0xBF ).
SPI Status [0x0B]: Sending this command asks for the EM260 status. The response status byte will always have
the upper 2 bits set. In this current version, the status byte only has one status bit [0], which is set if the
EM260 is alive and ready for commands.
Bootloader Frame [0xFD]: This byte indicates that the current transaction is a Bootloader transaction and
there is more data to follow. This SPI Byte will cause the transaction to look like the full data format
illustrated in Figure 8. The byte immediately after this SPI Byte will be a Length Byte, and it is used to
identify the length of the Bootloader Frame. Refer to document UG103.6, Ember Application Development
Fundamentals: Bootloading , for more information on the bootloader. If the SPI Byte is 0xFD , it means the
minimum transaction size is four bytes.
EZSP Frame [0xFE]: This byte indicates that the current transaction is an EZSP transaction and there is more
data to follow. This SPI Byte will cause the transaction to look like the full data format illustrated in Figure
8. The byte immediately after this SPI Byte will be a Length Byte, and it is used to identify the length of
the EZSP Frame. (The EZSP Frame is defined in document UG100, EZSP Reference Guide .) If the SPI Byte is
0xFE , it means the minimum transaction size is five bytes.
5.5.2
Special Response Bytes
There are only five SPI Byte values, 0x00–0x04 , ever used as error codes (see Table 16). When the error
condition occurs, any command sent to the EM260 will be ignored and responded to with one of these codes.
These special SPI Bytes must be trapped and dealt with. In addition, for each error condition the Error Byte
(instead of the Length Byte) is also sent with the SPI Byte.
Table 16. Byte Values Used as Error Codes
SPI Byte
Error Message
Error Description
Error Byte Description
Value
0x00
EM260 Reset
See section 5.6, Powering On, Power
Cycling, and Rebooting.
The reset type. Refer to API
documentation discussing
EmberResetType.
0x01
Oversized EZSP
Frame
The command contained an EZSP
frame with a Length Byte greater than
Reserved
133. The EM260 was forced to drop the
entire command.
0x02
Aborted
Transaction
The transaction was not completed
properly and the EM260 was forced to
Reserved
abort the transaction.
0x03
Missing Frame
Terminator
The command was missing the Frame
Terminator. The EM260 was forced to
Reserved
drop the entire command.
0x04
Unsupported SPI
Command
The command contained an
unsupported SPI Byte. The EM260 was
Reserved
forced to drop the entire command.
5.6
Powering On, Power Cycling, and Rebooting
When the Host powers on (or reboots), it cannot guarantee that the EM260 is awake and ready to receive
commands. Therefore, the Host should always perform the Wake EM260 handshake to guarantee that the
EM260 is awake. If the EM260 resets, it needs to inform the Host so that the Host can reconfigure the stack if
needed.
120-0260-000M Rev 1.1
Page 28
相关PDF资料 |
PDF描述 |
|---|---|
| EM35X-NCP-ADD-ON-S | EM35X ADD ON KIT |
| EM6J1T2R | MOSFET 2P-CH 20V 200MA EMT6 |
| EM6K6T2R | MOSFET 2N-CH 20V 300MA EMT6 |
| EM6K7T2R | MOSFET 2N-CH 20V 200MA EMT6 |
| EM6M1T2R | MOSFET N/P-CH 30V .1A EMT6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EM260-DEV | 功能描述:KIT DEV FOR EM260 RoHS:否 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:InSight 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
| EM260-RCM-USART-R | 功能描述:EM260 RCM BOARD RoHS:是 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
| EM260-RTR | 功能描述:IC ZIGBEE SYSTEM-ON-CHIP 40-QFN RoHS:是 类别:RF/IF 和 RFID >> RF 收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:30 系列:- 频率:4.9GHz ~ 5.9GHz 数据传输率 - 最大:54Mbps 调制或协议:* 应用:* 功率 - 输出:-3dBm 灵敏度:- 电源电压:2.7 V ~ 3.6 V 电流 - 接收:* 电流 - 传输:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 工作温度:-25°C ~ 85°C 封装/外壳:68-TQFN 裸露焊盘 包装:管件 |
| EM260-RTY | 功能描述:IC ZIGBEE SYSTEM-ON-CHIP 40-QFN RoHS:是 类别:RF/IF 和 RFID >> RF 收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:30 系列:- 频率:4.9GHz ~ 5.9GHz 数据传输率 - 最大:54Mbps 调制或协议:* 应用:* 功率 - 输出:-3dBm 灵敏度:- 电源电压:2.7 V ~ 3.6 V 电流 - 接收:* 电流 - 传输:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 工作温度:-25°C ~ 85°C 封装/外壳:68-TQFN 裸露焊盘 包装:管件 |
| EM260-USART-JMP-R | 功能描述:KIT JUMP START FOR EM260 RoHS:否 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:JumpStart 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
发布紧急采购，3分钟左右您将得到回复。