参数资料
| 型号： | HW-USB-II-G |
| 厂商： | Xilinx Inc |
| 文件页数： | 4/35页 |
| 文件大小： | 0K |
| 描述： | PLATFORM CABLE USB II |
| 产品培训模块： | Extended Spartan 3A FPGA Family S6 Family Overview |
| 标准包装： | 1 |
| 附件类型： | USB 平台线缆 |
| 适用于相关产品： | Xilinx FPGA、CPLDS、平台闪存 PROM、XC18V00 PROM、系统 ACE MPM |
| 产品目录页面： | 600 (CN2011-ZH PDF) |
| 其它名称： | 122-1572 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
Platform Cable USB II
Table 1: Platform Cable USB II Software Compatibility
Software
ISE Foundation / ISE WebPACK
ChipScope Pro Analyzer
Embedded Development Kit
System Generator for DSP
Notes:
Version
6.3i SP3 and later
6.3i SP3 and later
7.1i and later
8.1i and later
1.
An installer must be run to enable Platform Cable USB II for use
The minimum system requirements for these applications are located on the Xilinx website at:
Note: To receive the current enhancements and bug fixes, Xilinx recommends using the newest version of a tool and applying the latest
service pack.
Operating Power
Platform Cable USB II is a bus-powered device (drawing less than 150 mA from the host USB port under all operating
conditions), automatically adapting to the capabilities of the host USB port to achieve the highest possible performance.
Platform Cable USB II enumerates on any USB port type: USB ports on root hubs, external bus-powered hubs, external self-
powered hubs and legacy USB 1.1 hubs (see USB Hub Types and Cable Performance, page 28 ). However, performance is
not optimal when attached to USB 1.1 hubs (refer to Hot Plug and Play, page 5 for an explanation of USB enumeration).
Device Driver Installation
For a complete guide to installation of the Platform Cable USB II refer to UG344 , USB Cable Installation Guide .
A proprietary device driver is required to use Platform Cable USB II. This driver is automatically installed when a supported
Xilinx design tool is installed.
Note: Automatic driver installation is available beginning with version 10.1 of Xilinx design tools. For earlier versions, a driver installer
must be run prior to using the cable. Refer to the USB Cable Installation Guide for instructions on downloading and running the installer.
Firmware Updates
The Platform Cable USB II firmware resides in an USB microcontroller and a FPGA/PROM. The microcontroller is RAM-
based and firmware is downloaded each time the cable is connected and detected by the host operating system. Additional
firmware can also be downloaded to the microcontroller once a design tool establishes a connection with the cable. The USB
protocol guarantees that the firmware is successfully downloaded.
Upgraded firmware for the USB microcontroller is periodically distributed in Xilinx design tool releases or, on rare occasions,
in a Xilinx Answer Record . In most cases, an upgrade requires replacing one or more of the design tool's application files and
depending on operating system, one or more cable driver files.
Platform Cable USB II contains a Xilinx Spartan-3A FPGA with an in-system programmable Xilinx XCF02S PROM. Each
time a design tool establishes a connection with the cable, the firmware version stored in the PROM is examined. The PROM
is automatically reprogrammed over the cable if the firmware version is out of date. If an update is required, the design tool
displays the following warning message:
Warning: USB Cable firmware must be updated. This operation may take up to 40 seconds. Do not stop
the process or disconnect the cable prior to completion. The cable STATUS LED will be RED for the
duration of the update process.
Similarly, upgraded firmware for the FPGA/PROM is periodically distributed in Xilinx design tool releases or, on rare
occasions, in a Xilinx Answer Record . In most cases, an upgrade requires replacing a single design tool application file. The
PROM is reprogrammed with the new firmware the next time the tool connects to the cable. PROM reprogramming takes
DS593 (v1.2.1) March 17, 2011
4
相关PDF资料 |
PDF描述 |
|---|---|
| HW-USBN-2A | ACCY USB DOWNLOAD CABLE STD SPD |
| HW-V4-ML401-USA | EVALUATION PLATFORM VIRTEX-4 |
| HW-V4-ML423-UNI-G | EVALUATION PLATFORM VIRTEX-4 |
| HW-V4SX35-VIDEO-SK-UK | VIRTEX-4 VIDEO STARTER KIT |
| HW-V5-ML521-UNI-G | EVALUATION PLATFORM VIRTEX-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HW-USBN-2A | 功能描述:程序设计器配件 ispDOWNLOAD Cable RoHS:否 制造商:Lattice 产品:ispDOWNLOAD Cables 用于:In-system Programming |
| HW-USBN-2B | 功能描述:Lattice Programmable Products ispDOWNLOAD? In-System Programmer 制造商:lattice semiconductor corporation 系列:ispDOWNLOAD? 零件状态:有效 类型:系统内编程器 配套使用产品/相关产品:Lattice 可编程产品 内容:编程器 标准包装:1 |
| HW-UW 30 | 制造商:OK International (OKI) / Metcal 功能描述:WRAPPING AND UNWRAPPING TOOL HAND 制造商:OK International (OKI) / Metcal 功能描述:WRAPPING AND UNWRAPPING TOOL, HAND |
| HW-UW-18-19 | 功能描述:手工工具 WRAP-UNWRAP TOOL, 18-19 AWG RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| HW-UW18-19 | 制造商:Jonard Industries 功能描述:WRAP-UNWRAP TOOL, 18-19 AWG |
发布紧急采购，3分钟左右您将得到回复。