- 您现在的位置：买卖IC网 > PDF目录3948 > IDT70T653MS15BC8 (IDT, Integrated Device Technology Inc)IC SRAM 18MBIT 15NS 256BGA PDF资料下载
参数资料
| 型号： | IDT70T653MS15BC8 |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 19/24页 |
| 文件大小： | 0K |
| 描述： | IC SRAM 18MBIT 15NS 256BGA |
| 标准包装： | 1,000 |
| 格式 - 存储器： | RAM |
| 存储器类型： | SRAM - 双端口，异步 |
| 存储容量： | 18M（512K x 36） |
| 速度： | 15ns |
| 接口： | 并联 |
| 电源电压： | 2.4 V ~ 2.6 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 256-LBGA |
| 供应商设备封装： | 256-CABGA（17x17） |
| 包装： | 带卷 (TR) |
| 其它名称： | 70T653MS15BC8 |
IDT70T653M
High-Speed 2.5V 512K x 36 Asynchronous Dual-Port Static RAM
How the Semaphore Flags Work
The semaphore logic is a set of eight latches which are indepen-
dent of the Dual-Port RAM. These latches can be used to pass a flag,
or token, from one port to the other to indicate that a shared resource
is in use. The semaphores provide a hardware assist for a use
assignment method called “Token Passing Allocation.” In this method,
the state of a semaphore latch is used as a token indicating that a
shared resource is in use. If the left processor wants to use this
resource, it requests the token by setting the latch. This processor then
verifies its success in setting the latch by reading it. If it was successful, it
proceeds to assume control over the shared resource. If it was not
successful in setting the latch, it determines that the right side processor
has set the latch first, has the token and is using the shared resource.
Industrial and Commercial Temperature Ranges
subsequent read (see Table IV). As an example, assume a processor
writes a zero to the left port at a free semaphore location. On a
subsequent read, the processor will verify that it has written success-
fully to that location and will assume control over the resource in question.
Meanwhile, if a processor on the right side attempts to write a zero to the
same semaphore flag it will fail, as will be verified by the fact that a one will
be read from that semaphore on the right side during subsequent read.
Had a sequence of READ/WRITE been used instead, system contention
problems could have occurred during the gap between the read and write
cycles.
It is important to note that a failed semaphore request must be followed
by either repeated reads or by writing a one into the same location. The
reason for this is easily understood by looking at the simple logic diagram
The left processor can then either repeatedly request that
semaphore’s status or remove its request for that semaphore to
perform another task and occasionally attempt again to gain control of
the token via the set and test sequence. Once the right side has
L PORT
SEMAPHORE
REQUEST FLIP FLOP
R PORT
SEMAPHORE
REQUEST FLIP FLOP
relinquished the token, the left side should succeed in gaining control.
The semaphore flags are active LOW. A token is requested by
writing a zero into a semaphore latch and is released when the same
D 0
WRITE
D
Q
Q
D
D 0
WRITE
side writes a one to that latch.
The eight semaphore flags reside within the IDT70T653M in a
separate memory space from the Dual-Port RAM. This address space
is accessed by placing a low input on the SEM pin (which acts as a chip
select for the semaphore flags) and using the other control pins (Address,
SEMAPHORE
READ
Figure 4. IDT70T653M Semaphore Logic
SEMAPHORE
READ
5679 drw 21
CE 0 , CE 1 ,R/ W and BE n) as they would be used in accessing a
standard Static RAM. Each of the flags has a unique address which can
be accessed by either side through address pins A 0 – A 2 . When accessing
the semaphores, none of the other address pins has any effect.
When writing to a semaphore, only data pin D 0 is used. If a low level
is written into an unused semaphore location, that flag will be set to
a zero on that side and a one on the other side (see Truth Table IV).
That semaphore can now only be modified by the side showing the zero.
When a one is written into the same location from the same side, the flag
will be set to a one for both sides (unless a semaphore request
from the other side is pending) and then can be written to by both sides.
The fact that the side which is able to write a zero into a semaphore
subsequently locks out writes from the other side is what makes
semaphore flags useful in interprocessor communications. (A thorough
discussion on the use of this feature follows shortly.) A zero written into the
same location from the other side will be stored in the semaphore request
latch for that side until the semaphore is freed by the first side.
When a semaphore flag is read, its value is spread into all data bits so
that a flag that is a one reads as a one in all data bits and a flag containing
a zero reads as all zeros for a semaphore read, the SEM , BE n, and OE
signals need to be active. (Please refer to Truth Table II). Furthermore,
the read value is latched into one side’s output register when that side's
semaphore select ( SEM , BE n) and output enable ( OE ) signals go active.
This serves to disallow the semaphore from changing state in the middle
of a read cycle due to a write cycle from the other side.
A sequence WRITE/READ must be used by the semaphore in
order to guarantee that no system level contention will occur. A
processor requests access to shared resources by attempting to write
a zero into a semaphore location. If the semaphore is already in use,
the semaphore request latch will contain a zero, yet the semaphore
flag will appear as one, a fact which the processor will verify by the
19
of the semaphore flag in Figure 4. Two semaphore request latches feed
into a semaphore flag. Whichever latch is first to present a zero to the
semaphore flag will force its side of the semaphore flag LOW and the other
side HIGH. This condition will continue until a one is written to the same
semaphore request latch. If the opposite side semaphore request latch has
been written to zero in the meantime, the semaphore flag will flip over to
the other side as soon as a one is written into the first request latch. The
opposite side flag will now stay LOW until its semaphore request latch is
written to a one. From this it is easy to understand that, if a semaphore is
requested and the processor which requested it no longer needs the
resource, the entire system can hang up until a one is written into that
semaphore request latch.
The critical case of semaphore timing is when both sides request a
single token by attempting to write a zero into it at the same time. The
semaphore logic is specially designed to resolve this problem. If simulta-
neous requests are made, the logic guarantees that only one side receives
the token. If one side is earlier than the other in making the request, the first
side to make the request will receive the token. If
both requests arrive at the same time, the assignment will be arbitrarily
made to one port or the other.
One caution that should be noted when using semaphores is that
semaphores alone do not guarantee that access to a resource is secure.
As with any powerful programming technique, if semaphores
are misused or misinterpreted, a software error can easily happen.
Initialization of the semaphores is not automatic and must be handled
via the initialization program at power-up. Since any semaphore request
flag which contains a zero must be reset to a one, all semaphores on both
sides should have a one written into them at initialization from both sides
to assure that they will be free when needed.
相关PDF资料 |
PDF描述 |
|---|---|
| MPC8544AVTANG | IC MPU POWERQUICC III 783-FCBGA |
| 1-1734798-2 | CONN HOUSING FPC 12POS R/A SMD |
| IDT70T3539MS133BC8 | IC SRAM 18MBIT 133MHZ 256BGA |
| 1-2013928-4 | CONN FPC 37POS .3MM FLIP LOC SMD |
| IDT70V5388S133BC8 | IC SRAM 1.125MBIT 133MHZ 256BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT70T659S10BC | 功能描述:IC SRAM 4MBIT 10NS 256BGA RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:3,000 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:8K (1K x 8) 速度:400kHz 接口:I²C，2 线串口 电源电压:1.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
| IDT70T659S10BC8 | 功能描述:IC SRAM 4MBIT 10NS 256BGA RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:3,000 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:8K (1K x 8) 速度:400kHz 接口:I²C，2 线串口 电源电压:1.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
| IDT70T659S10BCI | 功能描述:IC SRAM 4MBIT 10NS 256BGA RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:3,000 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:8K (1K x 8) 速度:400kHz 接口:I²C，2 线串口 电源电压:1.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
| IDT70T659S10BCI8 | 功能描述:IC SRAM 4MBIT 10NS 256BGA RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:3,000 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:8K (1K x 8) 速度:400kHz 接口:I²C，2 线串口 电源电压:1.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
| IDT70T659S10BF | 功能描述:IC SRAM 4MBIT 10NS 208FBGA RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:3,000 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:8K (1K x 8) 速度:400kHz 接口:I²C，2 线串口 电源电压:1.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。