- 您现在的位置：买卖IC网 > PDF目录17308 > ISL6232EVAL1 (Intersil)EVALUATION BOARD 1 ISL6232 PDF资料下载
参数资料
| 型号： | ISL6232EVAL1 |
| 厂商： | Intersil |
| 文件页数： | 18/25页 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD 1 ISL6232 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，LDO 步降 |
| 输出及类型： | 4，非隔离 |
| 输入电压： | 5.5 ~ 25 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 300kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ISL6232 |
ISL6232
includes its own internal digital soft-start circuit. In shutdown
or standby mode, the soft-start output is reset to zero.
Fault Protection
Undervoltage Protection
When the output undervoltage is detected at below 75%
(typ) of the regulation output for 20ms blanking time, it enters
the discharge mode by discharging the output through the
internal 20 Ω switch connected from PHASE to PGND. When
the output voltage drops below 0.3V, the external low side
MOSFET is latched on to discharge the output to ground.
When either output is in UVP, both outputs are latched off
through soft-discharge. The latches can be reset by toggling
V IN , SHDN#, or EN.
Overvoltage Protection
When either output voltage is above 113% (typ) of the
regulation point, both outputs are latched off by turning on
the low side MOSFET and turning off the high side MOSFET.
Discharging the output capacitors through the inductor and
low-side MOSFET causes negative output voltage. For loads
Thermal Protection
Thermal-overload protection limits total power dissipation in
the device. When the junction temperature exceeds +150°C,
a thermal sensor forces most of the internal circuitry into
shutdown mode, thus allowing the device to cool down. The
thermal sensor turns the device on again after the junction
temperature drops by +25°C, causing a pulsed output during
continuous overload conditions. The digital soft-start
sequence begins after the thermal shutdown condition is
removed.
Power-Up Sequence
EN3 and EN5 control the power-up sequencing of buck
controllers. Setting EN above 2.4V enables the outputs, and
setting EN below 0.8V disables the outputs. Connecting EN3
or EN5 to REF forces the respective output off until the other
output reaches 90% of the regulation point and soft-start
cycle has ended. One of the buck controllers can remain on
even though the other buck controller turns off. Table 2
shows the power sequence selection.
TABLE 2. POWER-UP SEQUENCE TABLE
that cannot tolerate a negative voltage, place a 1A power
Schottky diode across the output to act as a reverse-polarity
SHDN#
EN3
EN5
LDO3
LDO5 5V BUCK
3.3V
BUCK
clamp. If the overvoltage is due to a short in the high side
MOSFET, the battery fuse will be blown and isolated from
the output.
Overcurrent Protection
The output current is continuously monitored through either
an accurate sensing resistor or the DCR of the inductor.
When the inductor peak current reaches the overcurrent limit
threshold, it immediately turn off the high side MOSFET and
turn on the low side MOSFET. This peak current limiting
prevents inductor saturation. If the overcurrent or short
circuit condition is detected for more than 20ms (typ), the
Low
High
High
High
High
High
High
x
Low
Low
High
High
High
REF
x
Low
High
Low
High
REF
High
OFF
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
OFF
ON
ON after
3.3V up
ON
OFF
OFF
OFF
ON
ON
ON
ON after
5V up
high side MOSFET is latched off and the output is
discharged through the internal 20 Ω switch connected from
PHASE to PGND. When the output voltage drops below
0.3V, the low side MOSFET is latched on to discharge the
output to ground. When either output is latched off due to
overcurrent, the other output is also latched off through
soft-discharge.
18
SHUTDOWN MODE
When SHDN# is set below 0.8V, the part is completely shut
down with a 5μA (typ) shutdown V IN current. When SHDN#
is set above 2.4V, both LDO outputs and REF are active.
This is prerequisite for enabling buck controllers. For
automatic shutdown and startup, SHDN# can be tied to V IN .
Table 3 is the summary of various operation modes.
FN9116.1
April 20, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| RBC20DRXI | CONN EDGECARD 40POS DIP .100 SLD |
| MC33880DWB | IC SWITCH 8X WITH SPI 32-SOIC |
| RCC20DRES | CONN EDGECARD 40POS .100 EYELET |
| ZL6100EVAL1Z | EVAL BOARD USB ZL6100 |
| EGP30FHE3/54 | DIODE 3A 300V 50NS GP20 AXIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6235 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Advanced Triple PWM Only Mode and Dual Linear Power Controller for Portable Applications |
| ISL6235CA | 制造商:Rochester Electronics LLC 功能描述:SYSTEM ELECTRONICS REGULATOR FOR LCD-PC - Bulk |
| ISL6235CA-T | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| ISL6236 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers |
| ISL6236A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers |
发布紧急采购，3分钟左右您将得到回复。