- 您现在的位置：买卖IC网 > PDF目录17308 > ISL6232EVAL1 (Intersil)EVALUATION BOARD 1 ISL6232 PDF资料下载
参数资料
| 型号： | ISL6232EVAL1 |
| 厂商： | Intersil |
| 文件页数： | 24/25页 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD 1 ISL6232 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，LDO 步降 |
| 输出及类型： | 4，非隔离 |
| 输入电压： | 5.5 ~ 25 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 300kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ISL6232 |
ISL6232
The power requirements of the auxiliary supply must be
considered in the design of the main output. The flyback
transformer must be designed to deliver the required current
in both the primary and the secondary outputs with the
proper turns ratio and inductance. The overcurrent limit
threshold may also be adjusted accordingly. Power from the
main and secondary outputs is combined to get an
equivalent current referred to the main output, which is given
by Equation 32.
PCB Layout Guidelines
Careful PC board layout is critical to achieve minimal
switching losses and clean, stable operation. This is
especially true when multiple converters are on the same PC
circuit board, where one circuit can affect the other due to
the noise coupling through the power ground. The switching
power stages require particular attention. Mount all of the
power components on the top-side of the board with their
ground terminals flush against one another, if possible.
I total = -------------------------------------------------
P main + P auxiliary
V OUT
(EQ. 32)
Use the following guidelines for good PC board layout:
? Isolate the power components from the sensitive analog
where P main and P auxiliary are the main power and auxiliary
power, respectively.
For the circuit in Figure 35, the turns ratio N of the flyback is
determined by Equation 33.
components. Use a separate power plane ground and
signal power ground if possible.
? Use a star ground connection on the power plane to
minimize the cross-talk between OUT3 and OUT5.
V SEC + V F – V OUT
N = ---------------------------------------------------
V OUT + V RECT
(EQ. 33)
? Keep the high-current paths short, especially at the
ground terminals. This practice is essential for stable,
jitter-free operation.
where, V SEC is the minimum required rectified secondary
voltage, V F is the forward voltage drop across the secondary
rectifier, and V RECT is the on-state voltage drop across the
synchronous rectifier MOSFET. The secondary rectifier in
the flyback must withstand flyback voltages, which is given
by Equation 34.
? Keep the power traces and load connections short. This
practice is essential for high efficiency. Using thick copper
PC boards (2oz vs 1oz) can enhance full-load efficiency
by 1% or more. Correctly routing PC board traces must be
approached in terms of fractions of centimeters, where a
single milliohm of excess trace resistance causes a
measurable efficiency loss.
V REV = V SEC + N ? ( V IN – V OUT )
(EQ. 34)
? When trade-offs in trace lengths must be made, it is
preferable to allow the inductor-charging path to be made
The secondary rectifier's reverse breakdown voltage rating
must also accommodate any ringings due to leakage
inductance. This voltage ringings can be minimized by
adding a snubber circuit across the secondary rectifier. Its
current rating should be at least twice the DC load current on
the auxiliary output. The optional linear post regulator must
be selected to deliver the required load current, and it should
be configured to run close to dropout to minimize power
dissipation.
longer than the discharge path. For example, it is better to
allow some extra distance between the input capacitors
and the high-side MOSFET than to allow distance
between the inductor and the synchronous rectifier or
between the inductor and the output filter capacitor,
because the synchronous rectifier conduction time is
usually longer than that of high-side MOSFET.
? Ensure that the OUT connection to the output capacitors is
short and direct. This reduces the voltage spike or dip due
to the trace resistance between OUT and output
capacitors.
LDO
Optional
12V
? Route high-speed switching nodes (BOOT, UGATE,
PHASE, and LGATE) away from sensitive analog areas
(REF, COMP, FB, and CS). Use PGND3 and PGND5 as
ISL6232
BOOT5
UGATE5
PHASE5
Q1
Q2
D1
1:
N
?
T: L1- 6.8 μH
R
D2
OUT5
12V/20mA
4.7μF
an EMI shield to keep radiated switching noise away from
the ICs feedback divider and analog bypass capacitors.
? Keep the FB traces as short as possible for good radiated
immunity design.
LGATE5
N = 2.2
T: Delta Electronics
STQ125-6822
FIGURE 35. FLYBACK SECONDARY OUTPUT
24
FN9116.1
April 20, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| RBC20DRXI | CONN EDGECARD 40POS DIP .100 SLD |
| MC33880DWB | IC SWITCH 8X WITH SPI 32-SOIC |
| RCC20DRES | CONN EDGECARD 40POS .100 EYELET |
| ZL6100EVAL1Z | EVAL BOARD USB ZL6100 |
| EGP30FHE3/54 | DIODE 3A 300V 50NS GP20 AXIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6235 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Advanced Triple PWM Only Mode and Dual Linear Power Controller for Portable Applications |
| ISL6235CA | 制造商:Rochester Electronics LLC 功能描述:SYSTEM ELECTRONICS REGULATOR FOR LCD-PC - Bulk |
| ISL6235CA-T | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| ISL6236 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers |
| ISL6236A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers |
发布紧急采购，3分钟左右您将得到回复。