参数资料
| 型号： | ISL6312IRZ |
| 厂商： | Intersil |
| 文件页数： | 22/35页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM 4PHASE BUCK 48-QFN |
| 标准包装： | 43 |
| 应用： | 控制器，Intel VR10、VR11、AMD CPU |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.38 V ~ 1.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（7x7） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
ISL6312
Initialization
Prior to initialization, proper conditions must exist on the EN,
VCC, PVCC and the VID pins. When the conditions are met,
the controller begins soft-start. Once the output voltage is
within the proper window of operation, the controller asserts
PGOOD.
In order for the ISL6312 to begin operation, PVCC1 is the
only pin that is required to have a voltage applied that
exceeds POR. However, for 2 or 3-phase operation
PVCC2 and PVCC3 must also exceed the POR
threshold. Hysteresis between the rising and falling
thresholds assure that once enabled, the ISL6312 will not
inadvertently turn off unless the PVCC bias voltage drops
substantially (see “Electrical Specifications” on page 6).
ISL6312 INTERNAL CIRCUIT
EXTERNAL CIRCUIT
VCC
PVCC1
+ 12 V
For Intel VR10, VR11 and AMD 6-bit modes of operation
these are the only conditions that must be met for the
controller to immediately begin the soft-start sequence. If
running in AMD 5-bit mode of operation there is one more
condition that must be met:
POR
CIRCUIT
ENABLE
COMPARATOR
+
-
EN
10.7k Ω
1.40k Ω
5. The VID code must not be 11111 in AMD 5-bit mode. This
code signals the controller that no load is present. The
controller will not allow soft-start to begin if this VID code
is present on the VID pins.
Once all of these conditions are met the controller will begin
the soft-start sequence and will ramp the output voltage up
0.85V
to the user designated level.
Intel Soft-Start
+
EN_PH4
The soft-start function allows the converter to bring up the
SOFT-START
AND
FAULT LOGIC
-
1.21V
output voltage in a controlled fashion, resulting in a linear
ramp-up. The soft-start sequence for the Intel modes of
operation is slightly different then the AMD soft-start
FIGURE 10. POWER SEQUENCING USING THRESHOLD-
SENSITIVE ENABLE (EN) FUNCTION
Enable and Disable
While in shutdown mode, the PWM outputs are held in a
high-impedance state to assure the drivers remain off. The
following input conditions must be met, for both Intel and
AMD modes of operation, before the ISL6312 is released
from shutdown mode to begin the soft-start start-up
sequence:
1. The bias voltage applied at VCC must reach the internal
power-on reset (POR) rising threshold. Once this
threshold is reached, proper operation of all aspects of
the ISL6312 is guaranteed. Hysteresis between the rising
and falling thresholds assure that once enabled, the
ISL6312 will not inadvertently turn off unless the bias
voltage drops substantially (see “Electrical
sequence.
For the Intel VR10 and VR11 modes of operation, the
soft-start sequence if composed of four periods, as shown in
Figure 11. Once the ISL6312 is released from shutdown and
page 22), the controller will have fixed delay period TD1.
After this delay period, the VR will begin first soft-start ramp
until the output voltage reaches 1.1V VBOOT voltage. Then,
the controller will regulate the VR voltage at 1.1V for another
fixed period TD3. At the end of TD3 period, ISL6312 will
read the VID signals. If the VID code is valid, ISL6312 will
initiate the second soft-start ramp until the output voltage
reaches the VID voltage plus/minus any offset or droop
voltage.
The soft-start time is the sum of the 4 periods as shown in
Equation 17.
Specifications” on page 6).
2. The voltage on EN must be above 0.85V. The EN input
allows for power sequencing between the controller bias
voltage and another voltage rail. The enable comparator
holds the ISL6312 in shutdown until the voltage at EN
rises above 0.85V. The enable comparator has 110mV of
hysteresis to prevent bounce.
3. The voltage on the EN_PH4 pin must be above 1.21V.
The EN_PH4 input allows for power sequencing between
the controller and the external driver.
4. The driver bias voltage applied at the PVCC pins must
reach the internal power-on reset (POR) rising threshold.
22
T SS = TD1 + TD2 + TD3 + TD4
(EQ. 17)
FN9289.6
February 1, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| 315MXC680MEFCSN30X50 | CAP ALUM 680UF 315V 20% SNAP-IN |
| HMC17DRAS-S734 | CONN EDGECARD 34POS .100 R/A PCB |
| HSC13DRAI-S734 | CONN EDGECARD 26POS .100 R/A PCB |
| GMC22DRXS-S734 | CONN EDGECARD 44POS DIP .100 SLD |
| 350MXC560MEFCSN35X40 | CAP ALUM 560UF 350V 20% SNAP-IN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6312IRZ-T | 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6313BCRZ | 功能描述:IC CTRLR PWM BUCK 2PHASE 36-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6313BCRZ-T | 功能描述:IC CTRLR PWM 2PHASE BUCK 36-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6313BIRZ | 功能描述:IC CTRLR PWM 2PHASE BUCK 36-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6313BIRZ-T | 功能描述:IC CTRLR PWM BUCK 2PHASE 36-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。