参数资料
| 型号： | ISL6312IRZ |
| 厂商： | Intersil |
| 文件页数： | 9/35页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM 4PHASE BUCK 48-QFN |
| 标准包装： | 43 |
| 应用： | 控制器，Intel VR10、VR11、AMD CPU |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.38 V ~ 1.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（7x7） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
ISL6312
Functional Pin Descriptions
VCC
VCC is the bias supply for the ICs small-signal circuitry.
Connect this pin to a +5V supply and decouple using a
quality 0.1μF ceramic capacitor.
PVCC1_2 and PVCC3
These pins are the power supply pins for the corresponding
channel MOSFET drive, and can be connected to any
voltage from +5V to +12V depending on the desired
MOSFET gate-drive level. Decouple these pins with a quality
1.0μF ceramic capacitor.
Leaving PVCC3 unconnected or grounded programs the
controller for 2-phase operation.
GND
GND is the bias and reference ground for the IC.
EN
This pin is a threshold-sensitive (approximately 0.85V) enable
input for the controller. Held low, this pin disables controller
operation. Pulled high, the pin enables the controller for
operation.
FS
A resistor, placed from FS to ground, sets the switching
frequency of the controller.
VID0, VID1, VID2, VID3, VID4, VID5, VID6, and VID7
These are the inputs for the internal DAC that provides the
reference voltage for output regulation. These pins respond to
TTL logic thresholds. These pins are internally pulled high, to
approximately 1.2V, by 40μA internal current sources for Intel
modes of operation, and pulled low by 20μA internal current
sources for AMD modes of operation. The internal pull-up
current decreases to 0 as the VID voltage approaches the
internal pull-up voltage. All VID pins are compatible with
external pull-up voltages not exceeding the IC’s bias voltage
(VCC).
VRSEL
The state of this pin selects which of the available DAC tables
will be used to decode the VID inputs and puts the controller
into the corresponding mode of operation. Refer to Table 1 for
available options and details of implementation.
VSEN and RGND
VSEN and RGND are inputs to the precision differential
remote-sense amplifier and should be connected to the sense
pins of the remote load.
VDIFF
VDIFF is the output of the differential remote-sense amplifier.
The voltage on this pin is equal to the difference between
VSEN and RGND.
9
FB and COMP
These pins are the internal error amplifier inverting input and
output respectively. FB, VDIFF, and COMP are tied together
through external R-C networks to compensate the regulator.
IDROOP
The IDROOP pin is the average channel-current sense
output. Connecting this pin through a tuned parallel R-C
network to FB allows the converter to incorporate output
voltage droop proportional to the output current. If voltage
droop is not desired leave this pin unconnected.
REF
The REF input pin is the positive input of the error amplifier. It
is internally connected to the DAC output through a 1k Ω
resistor. A capacitor is used between the REF pin and ground
to smooth the voltage transition during Dynamic VID
operations.
OFS
The OFS pin provides a means to program a DC current for
generating an offset voltage across the resistor between FB
and VDIFF. The offset current is generated via an external
resistor and precision internal voltage references. The polarity
of the offset is selected by connecting the resistor to GND or
VCC. For no offset, the OFS pin should be left unconnected.
ISEN1-, ISEN1+, ISEN2-, ISEN2+, ISEN3-, ISEN3+,
ISEN4-, and ISEN4+
These pins are used for differentially sensing the
corresponding channel output currents. The sensed currents
are used for channel balancing, protection, and load line
regulation.
Connect ISEN1-, ISEN2-, ISEN3-, and ISEN4- to the node
between the RC sense elements surrounding the inductor of
their respective channel. Tie the ISEN+ pins to the VCORE
side of their corresponding channel’s sense capacitor.
UGATE1, UGATE2, and UGATE3
Connect these pins to the corresponding upper MOSFET
gates. These pins are used to control the upper MOSFETs
and are monitored for shoot-through prevention purposes.
BOOT1, BOOT2, and BOOT3
These pins provide the bias voltage for the corresponding
upper MOSFET drives. Connect these pins to appropriately-
chosen external bootstrap capacitors. Internal bootstrap
diodes connected to the PVCC pins provide the necessary
bootstrap charge.
FN9289.6
February 1, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| 315MXC680MEFCSN30X50 | CAP ALUM 680UF 315V 20% SNAP-IN |
| HMC17DRAS-S734 | CONN EDGECARD 34POS .100 R/A PCB |
| HSC13DRAI-S734 | CONN EDGECARD 26POS .100 R/A PCB |
| GMC22DRXS-S734 | CONN EDGECARD 44POS DIP .100 SLD |
| 350MXC560MEFCSN35X40 | CAP ALUM 560UF 350V 20% SNAP-IN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6312IRZ-T | 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6313BCRZ | 功能描述:IC CTRLR PWM BUCK 2PHASE 36-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6313BCRZ-T | 功能描述:IC CTRLR PWM 2PHASE BUCK 36-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6313BIRZ | 功能描述:IC CTRLR PWM 2PHASE BUCK 36-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6313BIRZ-T | 功能描述:IC CTRLR PWM BUCK 2PHASE 36-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。