参数资料
| 型号： | ISL6313IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 24/33页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM 2PHASE BUCK 36-QFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 4,000 |
| 应用： | 控制器，Intel VR11，AMD CPU |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.5 V ~ 1.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-WFQFN 裸露焊盘 |
| 供应商设备封装： | 36-TQFN 裸露焊盘（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
ISL6313
pin voltage exceeds the V OCP voltage of 2.0V, the
overcurrent protection circuitry activates. Since the IOUT pin
voltage is proportional to the output current, the overcurrent
trip level, I OCP , can be set by selecting the proper value for
R IOUT , as shown in Equation 24.
During VID-on-the-fly transitions the OCL trip level is
boosted to prevent false overcurrent limiting events that can
occur. Starting from the beginning of a dynamic VID
transition, the overcurrent trip level is boosted to 196μA. The
OCL level will stay at this boosted level until 50μs after the
DCR ? R IOUT ? 400
6 ? R SET ? N
I OCP = ---------------------------------------------------
(EQ. 24)
end of the dynamic VID transition, at which point it will return
to the typical 140μA trip level.
Once the output current exceeds the overcurrent trip level,
V IOUT will exceed V OCP and a comparator will trigger the
converter to begin overcurrent protection procedures.
At the beginning of an overcurrent shutdown, the controller
turns off both upper and lower MOSFETs and lowers
PGOOD. The controller will then immediately attempt to soft-
start. If the overcurrent fault remains, the trip-retry cycles will
continue until either the controller is disabled or the fault is
cleared. If five overcurrent events occur without successfully
completing soft-start, the controller will latch off after the fifth
try and must be reset by toggling EN before a soft-start can
be reinitiated. Note that the energy delivered during trip-retry
cycling is much less than during full-load operation, so there
is no thermal hazard.
OUTPUT CURRENT, 50A/DIV
0A
OUTPUT VOLTAGE,
500mV/DIV
0V
FIGURE 17. OVERCURRENT BEHAVIOR IN HICCUP MODE
Individual Channel Overcurrent Limiting
The ISL6313 has the ability to limit the current in each
individual channel without shutting down the entire regulator.
This is accomplished by continuously comparing the sensed
currents of each channel with a constant 140μA OCL
reference current as shown in Figure 17. If a channel’s
individual sensed current exceeds this OCL limit, the UGATE
signal of that channel is immediately forced low, and the
LGATE signal is forced high. This turns off the upper
General Design Guide
This design guide is intended to provide a high-level
explanation of the steps necessary to create a multi-phase
power converter. It is assumed that the reader is familiar with
many of the basic skills and techniques referenced below. In
addition to this guide, Intersil provides complete reference
designs that include schematics, bills of materials, and example
board layouts for all common microprocessor applications.
Power Stages
The first step in designing a multi-phase converter is to
determine the number of phases. This determination
depends heavily on the cost analysis which in turn depends
on system constraints that differ from one design to the next.
Principally, the designer will be concerned with whether
components can be mounted on both sides of the circuit
board, whether through-hole components are permitted, the
total board space available for power-supply circuitry, and
the maximum amount of load current. Generally speaking,
the most economical solutions are those in which each
phase handles between 25A and 30A. All surface-mount
designs will tend toward the lower end of this current range.
If through-hole MOSFETs and inductors can be used, higher
per-phase currents are possible. In cases where board
space is the limiting constraint, current can be pushed as
high as 40A per phase, but these designs require heat sinks
and forced air to cool the MOSFETs, inductors and
heat-dissipating surfaces.
MOSFETS
The choice of MOSFETs depends on the current each
MOSFET will be required to conduct, the switching frequency,
the capability of the MOSFETs to dissipate heat, and the
availability and nature of heat sinking and air flow.
LOWER MOSFET POWER CALCULATION
The calculation for power loss in the lower MOSFET is
simple, since virtually all of the loss in the lower MOSFET is
due to current conducted through the channel resistance
(r DS(ON) ). In Equation 25, I M is the maximum continuous
output current, I P-P is the peak-to-peak inductor current (see
Equation 1), and d is the duty cycle (V OUT /V IN ).
? I M ? 2 I L ( P-P ) 2 ? ( 1 – d )
P LOW ( 1 ) = r DS ( ON ) ? ? ------ ? ? ( 1 – d ) + ----------------------------------------
MOSFET(s), turns on the lower MOSFET(s), and stops the
rise of current in that channel, forcing the current in the
channel to decrease. That channel’s UGATE signal will not
? N ? 12
(EQ. 25)
be able to return high until the sensed channel current falls
back below the 140μA reference.
24
An additional term can be added to the lower-MOSFET loss
equation to account for additional loss accrued during the dead
time when inductor current is flowing through the
FN6448.2
September 2, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ESM28DSAN | CONN EDGECARD 56POS R/A .156 SLD |
| LT1521IST-3.3#PBF | IC REG LDO 3.3V .3A SOT223-3 |
| RSM18DSUS | CONN EDGECARD 36POS DIP .156 SLD |
| 450MXG220MEFCSN25X40 | CAP ALUM 220UF 450V 20% SNAP-IN |
| ESM28DSAH | CONN EDGECARD 56POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6314CRZ | 功能描述:电压模式 PWM 控制器 1-PH PWM CNTRLR W/1 INTEGRTD DRVRS 32LD RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6314CRZ-T | 功能描述:IC CTRLR PWM 1PHASE BUCK 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6314CRZ-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6314CRZ-T W/GOLD BOND WIRE ONLY T&R - Tape and Reel |
| ISL6314CRZ-TS2568 | 制造商:Intersil Corporation 功能描述:- Tape and Reel |
| ISL6314IRZ | 功能描述:IC CTRLR PWM 1PHASE BUCK 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。