参数资料
| 型号： | ISL6328ACRZ |
| 厂商： | Intersil |
| 文件页数： | 22/33页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE REGULATOR |
| 标准包装： | 50 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
ISL6328A
N 1 V IN – N ? V OUT V OUT
I OCP = 100mA ? ------------ ? --- ? R ISEN – ------------------------------------ ? -------------
2 ? L ? f S V IN
In the event that during normal operation if the PVCC, VCC or
GVOT voltage falls back below the POR threshold, the pre-POR
overvoltage protection circuitry reactivates to protect from any
more pre-POR overvoltage events.
Undervoltage Detection
The undervoltage threshold is set at VDAC - 300mV typical. When
the output voltage (VSEN-RGND) is below the undervoltage
threshold, PGOOD gets pulled low. No other action is taken by the
controller. PGOOD will return high if the output voltage rises
above VDAC - 250mV typical.
Open Sense Line Protection
In the case that either of the remote sense lines, VSEN or GND,
become open, the ISL6328A is designed to detect this and shut
down the controller. This event is detected by monitoring small
currents that are fed out the VSEN and RGND pins. In the event of
an open sense line fault, the controller will continue to remain off
until the fault goes away, at which point the controller will re-
initiate a soft-start sequence.
Overcurrent Protection
The ISL6328A takes advantage of the proportionality between
the load current and the average current, I AVG , to detect an
detail on how the average current is measured. Once the average
current exceeds 100μA, a comparator triggers the converter to
begin overcurrent protection procedures.
The overcurrent trip threshold is dictated by the DCR of the
inductors, the number of active channels, the DC gain of the
inductor RC filter and the R ISEN resistor. The overcurrent trip
threshold is shown in Equation 21.
(EQ. 21)
DCR K
start, as shown in Figure 14. If the fault remains, the trip-retry
cycles will continue until either the fault is cleared or for a total of
seven attempts. If the fault is not cleared on the final attempt,
the controller disables UGATE and LGATE signals for both Core
and Northbridge and latches off requiring a POR of VCC to reset
the ISL6328A.
It is important to note that during soft-start, the overcurrent trip
point is increased by a factor of 1.35. If the fault draws enough
current to trip overcurrent during normal run mode, it may not
draw enough current during the soft-start ramp period to trip
overcurrent while the output is ramping up. If a fault of this type
is affecting the output, then the regulator will complete soft-start
and the trip-retry counter will be reset to zero. Once the regulator
has completed soft-start, the overcurrent trip point will return to
it’s nominal setting and an overcurrent shutdown will be initiated.
This will result in a continuous hiccup mode.
OUTPUT CURRENT, 50A/DIV
0A
OUTPUT VOLTAGE,
500mV/DIV
0V
3ms/DIV
FIGURE 14. OVERCURRENT BEHAVIOR IN HICCUP MODE
Note that the energy delivered during trip-retry cycling is much
R 2
R 1 + R 2
Where:
K = --------------------
less than during full-load operation, so there is no thermal
hazard.
CORE REGULATOR OVERCURRENT
f SW = Switching Frequency
Equation 21 is valid for both the Core regulator and the
Northbridge regulator. This equation includes the DC load current
as well as the total ripple current contributed by all the phases.
For the Northbridge regulator, N is 1.
During soft-start, the overcurrent trip point is boosted by a factor
of 1.35. Instead of comparing the average measured current to
100μA, the average current is compared to 135μA. Immediately
after soft-start is over, the comparison level changes to 100μA.
This is done to allow for start-up into an active load while still
supplying output capacitor in-rush current.
OVERCURRENT PROTECTION SHUTDOWN
At the beginning of overcurrent shutdown, the controller sets all
of the UGATE and LGATE signals low, puts PWM3 and PWM4 (if
active) in a high-impedance state, and forces VDDPWRGD low.
This turns off all of the upper and lower MOSFETs. The system
remains in this state for fixed period of 12ms. If the controller is
still enabled at the end of this wait period, it will attempt a soft-
22
The ISL6328A features a Dual Overcurrent Protection (OCP)
feature on the Core that allows AMD processors to “throttle” the
load current beyond the normal OCP threshold for brief periods of
time. These current spikes occur when idle processor cores are
enabled. Dual OCP is not enabled until soft-start is complete.
When the Core average sensed current, I AVG , exceeds 100μA,
the Core regulator does not immediately initiate overcurrent
protection shutdown. The ISL6328A will, instead, source an
amount of current out of the OCP pin that is equivalent to the
amount of sensed current that exceeds 100μA. A capacitor tied
between the OCP pin and ground will immediately begin
charging. If the voltage across the capacitor, and thus the voltage
on the OCP pin, exceeds 2V then the ISL6328A will immediately
initiate overcurrent protection shutdown. If I AVG decreases to a
level below 100μA prior to the voltage on the OCP pin exceeding
2V, then the OCP pin is internally pulled to ground and the
voltage on the OCP capacitor is discharged. If, at any time, the
average sensed current exceeds 145μA, the ISL6328A will
immediately initiate overcurrent protection shutdown.
FN7986.0
April 6, 2012
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6566CRZR5184 | IC CTRLR PWM 3PHASE BUCK 40-QFN |
| ISL6566IRZAR5184 | IC CTRLR PWM 3PHASE BUCK 40-QFN |
| EBA40DTKN | CONN EDGECARD 80POS DIP .125 SLD |
| EBA40DTKH | CONN EDGECARD 80POS DIP .125 SLD |
| GCB35DHBS | CONN EDGECARD 70POS R/A .050 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6328ACRZ-T | 功能描述:IC VOLTAGE REGULATOR RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:* 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6328AIRZ | 功能描述:IC VOLTAGE REGULATOR RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:* 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6328AIRZ-T | 功能描述:IC VOLTAGE REGULATOR RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:* 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6328CRZ | 功能描述:IC CTRLR PWM SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| ISL6328CRZ-T | 功能描述:IC CTRLR PWM SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。