参数资料
| 型号： | ISL6328ACRZ |
| 厂商： | Intersil |
| 文件页数： | 29/33页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE REGULATOR |
| 标准包装： | 50 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页
ISL6328A
0.3
0.2
0.1
I L(P-P) = 0
I L(P-P) = 0.25 I O
I L(P-P) = 0.5 I O
I L(P-P) = 0.75 I O
0.3
0.2
0.1
I L(P-P) = 0
I L(P-P) = 0.5 I O
I L(P-P) = 0.75 I O
0
0
0.2
0.4
0.6
0.8
1.0
0
0
0.2
0.4
0.6
0.8
1.0
DUTY CYCLE (V O/ V IN )
FIGURE 23. NORMALIZED INPUT-CAPACITOR RMS CURRENT vs
DUTY CYCLE FOR 4-PHASE CONVERTER
For a four-phase design, use Figure 23 to determine the
input-capacitor RMS current requirement set by the duty cycle,
maximum sustained output current (I O ), and the ratio of the
peak-to-peak inductor current (I L(P-P) ) to I O . Select a bulk
capacitor with a ripple current rating which will minimize the
total number of input capacitors required to support the RMS
current calculated.
The voltage rating of the capacitors should also be at least 1.25x
greater than the maximum input voltage. Figures 24 and 25 provide
the same input RMS current information for three-phase and
2-phase designs respectively. Use the same approach for selecting
the bulk capacitor type and number.
0.3
I L(P-P) = 0 I L(P-P) = 0.5 I O
I L(P-P) = 0.25 I O I L(P-P) = 0.75 I O
0.2
0.1
DUTY CYCLE (V IN/ V O )
FIGURE 25. NORMALIZED INPUT-CAPACITOR RMS
CURRENT FOR 2-PHASE CONVERTER
Layout Considerations
MOSFETs switch very fast and efficiently. The speed with which
the current transitions from one device to another causes voltage
spikes across the interconnecting impedances and parasitic
circuit elements. These voltage spikes can degrade efficiency,
radiate noise into the circuit and lead to device overvoltage
stress. Careful component selection, layout, and placement
minimizes these voltage spikes. Consider, as an example, the
turnoff transition of the upper PWM MOSFET. Prior to turnoff, the
upper MOSFET was carrying channel current. During the turnoff,
current stops flowing in the upper MOSFET and is picked up by
the lower MOSFET. Any inductance in the switched current path
generates a large voltage spike during the switching interval.
Careful component selection, tight layout of the critical
components, and short, wide circuit traces minimize the
magnitude of voltage spikes.
There are two sets of critical components in a DC/DC converter
using a ISL6328A controller. The power components are the
most critical because they switch large amounts of energy. Next
are small signal components that connect to sensitive nodes or
supply critical bypassing current and signal coupling.
The power components should be placed first, which include the
MOSFETs, input and output capacitors, and the inductors. It is
important to have a symmetrical layout for each power train,
preferably with the controller located equidistant from each.
Symmetrical layout allows heat to be dissipated equally across all
0
0 0.2 0.4 0.6 0.8
DUTY CYCLE (V IN/ V O )
FIGURE 24. NORMALIZED INPUT-CAPACITOR RMS CURRENT
FOR 3-PHASE CONVERTER
1.0
power trains. Equidistant placement of the controller to the CORE
and NB power trains it controls through the integrated drivers
helps keep the gate drive traces equally short, resulting in equal
trace impedances and similar drive capability of all sets of
MOSFETs.
Low capacitance, high-frequency ceramic capacitors are needed in
addition to the input bulk capacitors to suppress leading and
falling edge voltage spikes. The spikes result from the high current
slew rate produced by the upper MOSFET turn on and off. Select
low ESL ceramic capacitors and place one as close as possible to
each upper MOSFET drain to minimize board parasitics and
maximize suppression.
29
When placing the MOSFETs try to keep the source of the upper
FETs and the drain of the lower FETs as close as thermally possible.
Input high-frequency capacitors, C HF , should be placed close to the
drain of the upper FETs and the source of the lower FETs. Input
bulk capacitors, CBULK, case size typically limits following the
same rule as the high-frequency input capacitors. Place the input
FN7986.0
April 6, 2012
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6566CRZR5184 | IC CTRLR PWM 3PHASE BUCK 40-QFN |
| ISL6566IRZAR5184 | IC CTRLR PWM 3PHASE BUCK 40-QFN |
| EBA40DTKN | CONN EDGECARD 80POS DIP .125 SLD |
| EBA40DTKH | CONN EDGECARD 80POS DIP .125 SLD |
| GCB35DHBS | CONN EDGECARD 70POS R/A .050 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6328ACRZ-T | 功能描述:IC VOLTAGE REGULATOR RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:* 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6328AIRZ | 功能描述:IC VOLTAGE REGULATOR RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:* 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6328AIRZ-T | 功能描述:IC VOLTAGE REGULATOR RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:* 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6328CRZ | 功能描述:IC CTRLR PWM SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| ISL6328CRZ-T | 功能描述:IC CTRLR PWM SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。