参数资料
| 型号： | ISL6328ACRZ |
| 厂商： | Intersil |
| 文件页数： | 26/33页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE REGULATOR |
| 标准包装： | 50 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页
ISL6328A
R 1 , NEW = R 1 , OLD ? ----------
Δ V
R 2 , NEW = R 2 , OLD ? ----------
V DROOP
R FB = -----------------------------------------------------
? OUT MAX
?
? ----------------------- ? DCR ?
? ?
------------------------------- > f 0
Case 1:
2 ? π ? f 0 ? V pp ? L ? C
2 ? π ? V PP ? R FB ? f 0
4. Select new values, R 1,NEW and R 2,NEW , for the time constant
resistors based on the original values, R 1,OLD and R 2,OLD ,
using Equations 33 and 34.
Δ V 1 (EQ. 33)
2
Δ V 1 (EQ. 34)
Δ V 2
5. Replace R 1 and R 2 with the new values and check to see that
the error is corrected. Repeat the procedure if necessary.
Loadline Regulation Resistor
The loadline regulation resistor, labeled R FB in Figure 8, sets
the desired loadline required for the application. Equation 35
can be used to calculate R FB .
MAX
I
(EQ. 35)
N
--------------------------------------------- ? K
R ISEN
To choose the value for R FB in this situation, please refer to
Compensation With Loadline Regulation
The load-line regulated converter behaves in a similar manner to
a peak current mode controller because the two poles at the
output filter L-C resonant frequency split with the introduction of
current information into the control loop. The final location of
these poles is determined by the system function, the gain of the
current signal, and the value of the compensation components,
R C and C C .
components depend on the relationships of f 0 to the L-C pole
frequency and the ESR zero frequency. For each of the following
three, there is a separate set of equations for the compensation
components.
In Equation 36, L is the per-channel filter inductance divided by
the number of active channels; C is the sum total of all output
capacitors; ESR is the equivalent series resistance of the bulk
output filter capacitance; and V P-P is the peak-to-peak sawtooth
signal amplitude as described in the “Electrical Specifications”
Once selected, the compensation values in Equation 36 assure a
stable converter with reasonable transient performance. In most
cases, transient performance can be improved by making
adjustments to R C . Slowly increase the value of R C while
observing the transient performance on an oscilloscope until no
further improvement is noted. Normally, C C will not need
adjustment. Keep the value of C C from Equation 36 unless some
performance issue is noted
The optional capacitor C 2 , is sometimes needed to bypass noise
away from the PWM comparator (see Figure 20). Keep a position
available for C 2 , and be prepared to install a high-frequency
capacitor of between 22pF and 150pF in case any leading edge
jitter problem is noted.
1
2 ? π ? L ? C
0.66 ? V
R C = R FB ? ------------------------------------------------------
IN
0.66 ? V IN
C C = --------------------------------------------------
------------------------------- ≤ f 0 < -----------------------------------
2 ? π ? L ? C
C 2 (OPTIONAL)
Case 2:
1 1
2 ? π ? C ? ESR
V PP ? ( 2 ? π ) 2 ? f 02 ? L ? C
C C = ----------------------------------------------------------------------------------
PP ? R FB ?
( 2 ? π ) 2 ? f 2 ? V L ? C
f 0 > -----------------------------------
R FB
R C
C C
COMP
FB
VSEN
ISL6328A
Case 3:
0.66 ? V
R C = R FB ? ---------------------------------------------------------------
IN
0.66 ? V IN
0
1
2 ? π ? C ? ESR
(EQ. 36)
R C = R FB ? -------------------------------------------
2 ? π ? V PP ? R FB ? f 0 ? L
FIGURE 20. COMPENSATION CONFIGURATION FOR
LOAD-LINE REGULATED ISL6328A CIRCUIT
Since the system poles and zero are affected by the values of the
components that are meant to compensate them, the solution to
the system equation becomes fairly complicated. Fortunately,
there is a simple approximation that comes very close to an
optimal solution. Treating the system as though it were a voltage-
mode regulator, by compensating the L-C poles and the ESR zero
of the voltage mode approximation, yields a solution that is
always stable with very close to ideal transient performance.
Select a target bandwidth for the compensated system, f 0 . The
target bandwidth must be large enough to assure adequate
transient performance, but smaller than 1/3 of the per-channel
switching frequency. The values of the compensation
26
2 ? π ? f 0 ? V pp ? L
0.66 ? V IN ? ESR
0.66 ? V IN ? ESR ? C
C C = --------------------------------------------------------------
Compensation Without Loadline Regulation
The non load-line regulated converter is accurately modeled as a
voltage-mode regulator with two poles at the L-C resonant
frequency and a zero at the ESR frequency. A type III controller,
as shown in Figure 21, provides the necessary compensation.
FN7986.0
April 6, 2012
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6566CRZR5184 | IC CTRLR PWM 3PHASE BUCK 40-QFN |
| ISL6566IRZAR5184 | IC CTRLR PWM 3PHASE BUCK 40-QFN |
| EBA40DTKN | CONN EDGECARD 80POS DIP .125 SLD |
| EBA40DTKH | CONN EDGECARD 80POS DIP .125 SLD |
| GCB35DHBS | CONN EDGECARD 70POS R/A .050 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6328ACRZ-T | 功能描述:IC VOLTAGE REGULATOR RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:* 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6328AIRZ | 功能描述:IC VOLTAGE REGULATOR RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:* 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6328AIRZ-T | 功能描述:IC VOLTAGE REGULATOR RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:* 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6328CRZ | 功能描述:IC CTRLR PWM SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| ISL6328CRZ-T | 功能描述:IC CTRLR PWM SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。