参数资料
| 型号： | ISL6566CR |
| 厂商： | Intersil |
| 文件页数： | 20/29页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM BUCK 3PHASE 40-QFN |
| 标准包装： | 50 |
| 应用： | 控制器，Intel VRM9，VRM10，AMD Hammer 应用 |
| 输入电压： | 3 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 1.6 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
ISL6566
If VSEN or RGND become opened, VDIFF falls, causing the
duty cycle to increase and the output voltage on IREF to
increase. If the voltage on IREF exceeds “VDIFF+1V”, the
controller will shut down. Once the voltage on IREF falls
below “VDIFF+1V”, the ISL6566 will restart at the beginning
of soft-start.
Overcurrent Protection
The ISL6566 detects overcurrent events by comparing the
droop voltage, V DROOP , to the OCSET voltage, V OCSET , as
shown in Figure 13. The droop voltage, set by the external
current sensing circuitry, is proportional to the output current
as shown in Equation 7. A constant 100 μ A flows through
R OCSET , creating the OCSET voltage. When the droop
voltage exceeds the OCSET voltage, the overcurrent
protection circuitry activates. Since the droop voltage is
proportional to the output current, the overcurrent trip level,
I MAX , can be set by selecting the proper value for R OCSET ,
as shown in Equation 14.
power converter. It is assumed that the reader is familiar with
many of the basic skills and techniques referenced below. In
addition to this guide, Intersil provides complete reference
designs that include schematics, bills of materials, and example
board layouts for all common microprocessor applications.
Power Stages
The first step in designing a multi-phase converter is to
determine the number of phases. This determination
depends heavily on the cost analysis which in turn depends
on system constraints that differ from one design to the next.
Principally, the designer will be concerned with whether
components can be mounted on both sides of the circuit
board, whether through-hole components are permitted, the
total board space available for power-supply circuitry, and
the maximum amount of load current. Generally speaking,
the most economical solutions are those in which each
phase handles between 25 and 30A. All surface-mount
designs will tend toward the lower end of this current range.
I MAX ? R COMP ? DCR
100 μ ? R S
R OCSET = ----------------------------------------------------------
(EQ. 14)
If through-hole MOSFETs and inductors can be used, higher
per-phase currents are possible. In cases where board
space is the limiting constraint, current can be pushed as
Once the output current exceeds the overcurrent trip level,
V DROOP will exceed V OCSET , and a comparator will trigger the
converter to begin overcurrent protection procedures. At the
beginning of overcurrent shutdown, the controller turns off both
upper and lower MOSFETs. The system remains in this state
for a period of 4096 switching cycles. If the controller is still
enabled at the end of this wait period, it will attempt a soft-start
(as shown in Figure 14). If the fault remains, the trip-retry cycles
will continue indefinitely until either the controller is disabled or
the fault is cleared. Note that the energy delivered during trip-
retry cycling is much less than during full-load operation, so
there is no thermal hazard.
OUTPUT CURRENT, 50A/DIV
high as 40A per phase, but these designs require heat sinks
and forced air to cool the MOSFETs, inductors and heat-
dissipating surfaces.
MOSFETS
The choice of MOSFETs depends on the current each
MOSFET will be required to conduct, the switching frequency,
the capability of the MOSFETs to dissipate heat, and the
availability and nature of heat sinking and air flow.
LOWER MOSFET POWER CALCULATION
The calculation for power loss in the lower MOSFET is
simple, since virtually all of the loss in the lower MOSFET is
due to current conducted through the channel resistance
(r DS(ON) ). In Equation 15, I M is the maximum continuous
output current, I PP is the peak-to-peak inductor current (see
Equation 1), and d is the duty cycle (V OUT /V IN ).
? I M ? 2 I L , PP ( 1 – d )
P LOW , 1 = r DS ( ON ) ? ------ ? ( 1 – d ) + --------------------------------
0A
? N ? 12
(EQ. 15)
An additional term can be added to the lower-MOSFET loss
OUTPUT VOLTAGE,
500mV/DIV
equation to account for additional loss accrued during the
dead time when inductor current is flowing through the
lower-MOSFET body diode. This term is dependent on the
0V
2ms/DIV
diode forward voltage at I M , V D(ON) , the switching
frequency, f S , and the length of dead times, t d1 and t d2 , at
the beginning and the end of the lower-MOSFET conduction
P LOW , 2 = V D ( ON ) f S ? ------ + I --------- ? t
I PP ?
? I
d1 + ? ------ – --------- ? t d2
FIGURE 14. OVERCURRENT BEHAVIOR IN HICCUP MODE
F SW = 500kHz
General Design Guide
interval respectively.
I M PP
? N 2 ?
M
? N 2 ?
(EQ. 16)
This design guide is intended to provide a high-level
explanation of the steps necessary to create a multi-phase
20
The total maximum power dissipated in each lower MOSFET
is approximated by the summation of P LOW,1 and P LOW,2 .
FN9178.4
March 9, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| X5168S8I-2.7AT1 | IC SUPERVISOR CPU 16K EE 8-SOIC |
| ECC44DRES-S734 | CONN EDGECARD 88POS .100 EYELET |
| ISL6563CR-T | IC CTRLR PWM MULTIPHASE 24-QFN |
| ISL6563CR | IC CTRLR PWM MULTIPHASE 24-QFN |
| X5168S8I-2.7 | IC SUPERVISOR CPU 16K EE 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6566CRR5184 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL6566CR-T | 功能描述:IC CTRLR PWM BUCK 3PHASE 40-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6566CRZ | 功能描述:IC CTRLR PWM BUCK 3PHASE 40QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6566CRZA | 制造商:Intersil Corporation 功能描述:CURRENT MODE PWM CNTRLR 0.8375V TO 1.6V 100A 40QFN EP - Rail/Tube |
| ISL6566CRZAR5184 | 功能描述:IC CTRLR PWM 3PHASE BUCK 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。