- 您现在的位置：买卖IC网 > PDF目录1832 > LTC3839EUH#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 32-QFN PDF资料下载
参数资料
| 型号： | LTC3839EUH#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/50页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 32-QFN |
| 标准包装： | 73 |
| 系列： | PolyPhase® |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 2MHz |
| 电源电压： | 4.5 V ~ 38 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
LTC3839
APPLICATIONS INFORMATION
Once the required output voltage and operating frequency
have been determined, external component selection is
driven by load requirement, and begins with the selec-
tion of inductors and current sense method (either sense
resistors R SENSE or inductor DCR sensing). Next, power
MOSFETs are selected. Finally, input and output capaci-
tors are selected.
Output Voltage Programming
As shown in Figure 1, an external resistor divider is
used from the regulated output to its ground references
to program the output voltage. The resistive divider is
tapped by the V OUTSENSE+ pin and the ground reference
is remotely sensed by the V OUTSENSE– pin. By regulating
the differential feedback voltages to the internal reference
0.6V, the resulting output voltage is:
V OUT – V OUTSENSE– = 0.6V ? (1 + R FB2 /R FB1 )
For example, if V OUT is programmed to 5V and the out-
put ground reference is sitting at –0.5V with respect to
SGND, then the absolute value of the output will be 4.5V
with respect to SGND. The minimum differential output
voltage is limited to the internal reference 0.6V, and the
maximum is 5.5V.
V OUT
Differential output sensing allows for more accurate output
regulation in high power distributed systems having large
line losses. Figure 2 illustrates the potential variations in
the power and ground lines due to parasitic elements.
The variations may be exacerbated in multi-application
systems with shared ground planes. Without differential
output sensing, these variations directly reflect as an error
in the regulated output voltage. The LTC3839’s differential
output sensing can correct for up to ±500mV of variation
in the output’s power and ground lines.
The LTC3839’s differential output sensing scheme is
distinct from conventional schemes where the regulated
output and its ground reference are directly sensed with
a difference amplifier whose output is then divided down
with an external resistor divider and fed into the error
amplifier input. This conventional scheme is limited by
the common mode input range of the difference amplifier
and typically limits differential sensing to the lower range
of output voltages.
The LTC3839 allows for seamless differential output sens-
ing by sensing the resistively divided feedback voltage
differentially. This allows for differential sensing in the full
output range from 0.6V to 5.5V. The difference amplifier
(DIFFAMP) has a bandwidth of 8MHz, high enough so that
it will not affect main loop compensation and transient
behavior.
To avoid noise coupling into the feedback voltage, the
LTC3839
V OUTSENSE+
V OUTSENSE–
R FB2
R FB1
C OUT
3839 F01
resistor dividers should be placed close to the V OUTSENSE+
and V OUTSENSE– pins. Remote output and ground traces
should be routed together as a differential pair to the
remote output. For best accuracy, these traces to the
remote output and ground should be connected as close
Figure 1. Setting Output Voltage
The V OUTSENSE+ pin is a high impedance pin with no in-
put bias current other than leakage in the nA range. The
V OUTSENSE– pin has about 30μA of current flowing out
of the pin.
as possible to the desired regulation point.
Switching Frequency Programming
The choice of operating frequency is a trade-off between
efficiency and component size. Lowering the operating fre-
quency improves efficiency by reducing MOSFET switching
losses but requires larger inductance and/or capacitance
3839fa
16
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3850IGN-2#TRPBF | IC REG CTRLR BUCK PWM CM 28-SSOP |
| LTC3850IGN#PBF | IC REG CTRLR BUCK PWM CM 28-SSOP |
| LTC3851EGN#PBF | IC REG CTRLR BUCK PWM CM 16-SSOP |
| LTC3851EMSE-1#PBF | IC REG CTRLR BUCK PWM CM 16-MSOP |
| LTC3852EUDD#PBF | IC REG CTRLR DOUBLER PWM 24-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3839IUH#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3839IUH#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3850EGN#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3850EGN#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3850EGN-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。