- 您现在的位置：买卖IC网 > PDF目录1832 > LTC3839EUH#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 32-QFN PDF资料下载
参数资料
| 型号： | LTC3839EUH#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 19/50页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 32-QFN |
| 标准包装： | 73 |
| 系列： | PolyPhase® |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 2MHz |
| 电源电压： | 4.5 V ~ 38 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
LTC3839
APPLICATIONS INFORMATION
recommended lower limits of V SENSE(MAX) (by each indi-
vidual channel, calculated as half of the 2-channel-sum) for
R SENSE RESISTOR
AND
PARASITIC INDUCTANCE
statistical tolerancing design of a 2-phase application are:
R
ESL
? 24mV at V RNG = 0.6V or SGND (30mV typical);
? 42mV at V RNG = 1V or INTV CC (50mV typical);
LTC3839
SENSE +
R F
C F F ≤ ESL/R S
POLE-ZERO
CANCELLATION
V OUT
? 85mV at V RNG = 2V (100mV typical).
Either worst-case or statistical limits can be chosen to
SENSE –
C F
R F
3839 F03a
establish absolute minimums for current limit of the
LTC3839. Linear guarantees the worst-case minimum
and maximum for each channel, but does not guarantee
any statistical distributions of or relationship between the
two channels.
R SENSE Inductor Current Sensing
FILTER COMPONENTS
PLACED NEAR SENSE PINS
Figure 3a. R SENSE Current Sensing
TO SENSE FILTER,
NEXT TO THE CONTROLLER
The LTC3839 can be configured to sense the inductor
currents through either low value series current sensing
resistors (R SENSE ) or inductor DC resistance (DCR). The
R SENSE
3839 F03b
C OUT
R SENSE =
I OUT(MAX) –
choicebetweenthetwocurrentsensingschemesislargely
a design trade-off between cost, power consumption and
accuracy. DCR sensing is becoming popular because it
saves expensive current sensing resistors and is more
power efficient, especially in high current applications.
However, current sensing resistors provide the most ac-
curate current limits for the controller.
A typical R SENSE inductor current sensing scheme is shown
in Figure 3a. The filter components (R F , C F ) need to be
placed close to the IC. The positive and negative sense
traces need to be routed as a differential pair close to-
gether and Kelvin (4-wire) connected underneath the sense
resistor, as shown in Figure 3b. Sensing current elsewhere
can effectively add parasitic inductance to the current sense
element, degrading the information at the sense terminals
and making the programmed current limit unpredictable.
R SENSE is chosen based on the required maximum output
current. Given the maximum current, I OUT(MAX) , maximum
sense voltage, V SENSE(MAX) , set by V RNG , and maximum
inductor ripple current ? I L(MAX) , the value of R SENSE can
be chosen as:
V SENSE(MAX)
Δ I L(MAX)
2
Figure 3b. Sense Lines Placement with Sense Resistor
Conversely, given R SENSE and I OUT(MAX) , V SENSE(MAX) and
thus V RNG voltage can be determined from the above equa-
tion. To ensure the maximum output current, sufficient
margin should be built in the calculations to account for
variations of LTC3839 under different operating conditions
and tolerances of external components.
Because of possible PCB noise in the current sensing
loop, the current sensing voltage ripple ? V SENSE = ? I L ?
R SENSE also needs to be checked in the design to get a
good signal-to-noise ratio. In general, for a reasonably
good PCB layout, 10mV of ? V SENSE is recommended as
a conservative number to start with, either for R SENSE or
Inductor DCR sensing applications.
For today’s highest current density solutions the value
of the sense resistor can be less than 1mΩ and the
peak sense voltage can be as low as 20mV. In addition,
inductor ripple currents greater than 50% with operation
up to 2MHz are becoming more common. Under these
conditions, the voltage drop across the sense resistor’s
parasitic inductance becomes more relevant. A small RC
3839fa
19
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3850IGN-2#TRPBF | IC REG CTRLR BUCK PWM CM 28-SSOP |
| LTC3850IGN#PBF | IC REG CTRLR BUCK PWM CM 28-SSOP |
| LTC3851EGN#PBF | IC REG CTRLR BUCK PWM CM 16-SSOP |
| LTC3851EMSE-1#PBF | IC REG CTRLR BUCK PWM CM 16-MSOP |
| LTC3852EUDD#PBF | IC REG CTRLR DOUBLER PWM 24-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3839IUH#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3839IUH#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3850EGN#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3850EGN#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3850EGN-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。