- 您现在的位置：买卖IC网 > PDF目录1832 > LTC3839EUH#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 32-QFN PDF资料下载
参数资料
| 型号： | LTC3839EUH#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/50页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 32-QFN |
| 标准包装： | 73 |
| 系列： | PolyPhase® |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 2MHz |
| 电源电压： | 4.5 V ~ 38 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
LTC3839
PIN FUNCTIONS
PHASMD (Pin 1): Phase Selector Input. This pin
determines the relative phases of channels and the
CLKOUT signal. With zero phase being defined as the
rising edge of TG1: Pulling this pin to SGND locks TG2 to
180°, and CLKOUT to 60°. Connecting this pin to INTV CC
locks TG2 to 240° and CLKOUT to 120°. Floating this pin
locks TG2 to 180° and CLKOUT to 90°.
MODE/PLLIN (Pin 2): Operation Mode Selection or External
Clock Synchronization Input. When this pin is tied to IN-
TV CC , forced continuous mode operation is selected. Tying
this pin to SGND allows discontinuous mode operation.
When an external clock is applied at this pin, both chan-
nels operate in forced continuous mode and synchronize
to the external clock.
CLKOUT (Pin 3): Clock Output of Internal Clock Genera-
tor. Its output level swings between INTV CC and SGND. If
clock input is present at the MODE/PLLIN pin, it will be
synchronized to the input clock, with phase set by the
PHASMD pin. If no clock is present at MODE/PLLIN, its
frequency will be set by the RT pin. To synchronize other
controllers, it can be connected to their MODE/PLLIN pins.
SGND (Pins 4, 29): Signal Ground. All small-signal analog
and compensation components should be connected to
this ground. Connect both SGND pins to the exposed pad
and PGND pin using a single PCB trace.
RT (Pin 5): Clock Generator Frequency Programming Pin.
Connect an external resistor from RT to SGND to program
the switching frequency between 200kHz and 2MHz. An
external clock applied to MODE/PLLIN should be within
±30% of this programmed frequency to ensure frequency
lock. When the RT pin is floating, the frequency is internally
set to be slightly under 200kHz.
ITH (Pins 6): Current Control Threshold. This pin is the
output of the error amplifier and the switching regulator’s
compensation point. The current comparator threshold
increases with this control voltage. The voltage ranges
from 0V to 2.4V, with 0.8V corresponding to zero sense
voltage (zero inductor valley current).
TRACK/SS (Pin 7): External Tracking and Soft-Start Input.
The LTC3839 regulates the feedback voltage (V OUTSENSE+
– V OUTSENSE– ) to the smaller of 0.6V or the voltage on the
TRACK/SS pin. An internal 1μA temperature-independent
pull-up current source is connected to TRACK/SS pin. A
capacitor to ground at this pin sets the ramp time to the
final regulated output voltage. Alternatively, another voltage
supply connected to this pin allows the output to track the
other supply during start-up.
V OUTSENSE+ (Pin 8): Differential Output Sense Amplifier
(+) Input. Connect this pin to a feedback resistor divider
between the positive and negative output capacitor ter-
minals of V OUT . In nominal operation the LTC3839 will
attempt to regulate the differential output voltage V OUT to
0.6V divided by the feedback resistor divider ratio.
V OUTSENSE– (Pin 9): Differential Output Sense Amplifier
(–) Input. Connect this pin to the negative terminal of the
output load capacitor of V OUT .
SENSE1 + , SENSE2 + (Pin 10, Pin 31): Differential Current
Sense Comparator (+) Inputs. The ITH pin voltage and
controlled offsets between the SENSE + and SENSE – pins
set the current trip threshold. The comparator can be used
for R SENSE sensing or inductor DCR sensing. For R SENSE
sensing, Kelvin (4-wire) connect the SENSE + pin to the
(+) terminal of R SENSE . For DCR sensing, tie the SENSE +
pins to the connection between the DCR sense capacitor
and sense resistor tied across the inductor.
SENSE1 – , SENSE2 – (Pin 11, Pin 30): Differential Current
Sense Comparator (–) Input. The comparator can be used
for R SENSE sensing or inductor DCR sensing. For R SENSE
sensing, Kelvin (4-wire) connect the SENSE – pin to the (–)
terminal of R SENSE . For DCR sensing, tie the SENSE – pin
to the DCR sense capacitor tied to the inductor V OUT node
connection. These pins also function as output voltage
sense pins for the top MOSFET on-time adjustment. The
impedance looking into these pins is different from the
SENSE + pins because there is an additional 500k internal
resistor from each of the SENSE – pins to SGND.
DTR (Pin 12): Detect Load-Release Transient for Overshoot
Reduction. When load current suddenly drops, if voltage on
this DTR pin drops below half of INTV CC , the bottom gate
(BG) could turn off, allowing the inductor current to drop
to zero faster, thus reducing the V OUT overshoot. (Refer
to Load-Release Transient Detection in the Applications
Information section for more details.) An internal 5μA
current source pulls this pin toward INTV CC . To disable
the DTR feature, simply tie the DTR pin to INTV CC .
3839fa
9
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3850IGN-2#TRPBF | IC REG CTRLR BUCK PWM CM 28-SSOP |
| LTC3850IGN#PBF | IC REG CTRLR BUCK PWM CM 28-SSOP |
| LTC3851EGN#PBF | IC REG CTRLR BUCK PWM CM 16-SSOP |
| LTC3851EMSE-1#PBF | IC REG CTRLR BUCK PWM CM 16-MSOP |
| LTC3852EUDD#PBF | IC REG CTRLR DOUBLER PWM 24-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3839IUH#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3839IUH#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3850EGN#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3850EGN#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3850EGN-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。