收藏本站
参数资料
型号： M30102F3TFP
元件分类： 微控制器/微处理器
英文描述： 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP48
封装： 7 X 7 MM, 0.50 MM PITCH, PLASTIC, LQFP-48
文件页数： 86/166页
文件大小： 2060K
代理商： M30102F3TFP
Under
development
Tentative Specifications REV.E1
Specifications in this manual are tentative and subject to change.
Mitsubishi microcomputers
M30100/M30102 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
23
Symbol
Address
When reset
CPSRF
008F16
0XXXXXXX2
Clock prescaler reset flag
Bit name
Function
Bit symbol
b7
b6
b5
b4
b3
b2
b1
b0
Clock prescaler reset flag
0 : No effect
1 : Prescaler is reset
(When read, the value is “0”)
CPSR
W
R
Nothing is assigned.
In an attempt to write to these bits, write “0”. The value, if read, turns out to be
indeterminate.
Clock Generating Circuit
b7
b6
b5
b4
b3
b2
b1
b0
RW
CM20
CM21
CM22
CM23
0
00
0
Oscillation stop detection register (Note 5)
Symbol
Address
When reset
CM2
000C16
0416
Bit name
Function
Bit symbol
Main clock switch bit
Oscillation stop detection
interrupt enable bit
0: The function is invalid.
1: The function is valid.
0: Select XIN clock.
1: Select ring oscillator.
0: Disabled
1: Enabled
0: XIN oscillating normally
1: XIN stopping abnormally
Oscillation stop
detection bit
Clock monitor bit
Reserved bit
Always set to "0"
Note 1: Set to “0” before stopping the oscillation of the main clock (XIN-XOUT).
(stop mode, low power dissipation mode, ring oscillation mode)
An oscillation stop is detected if the oscillation of the main clock (XIN-XOUT) is
stopped when the following two conditions are satisfied: (1) the oscillation stop
detection function is valid and (2) CM21=1.
Note 2: Valid when CM20=1.
Note 3: CM22 bit switches to “1“ automatically if an oscillation stop is detected when
both CM20 bit and CM 21 bit are “1”. CM22 bit cannot be cleared when CM23=1.
Note 4: This bit is valid when CM20 bit is “1”. Use this bit for the purpose of confirming
XIN operation for oscillation stop detection interrupt execution.
Note 5: In case of writing to this register, set bit 0 of the protect register(000A16) to "1".
(Note 3)
(Note 2)
(Note 1)
(Note 4)
Figure 1.8.5. Oscillation stop detection register and clock prescaler reset flag
1/32
fC32
XCIN
Clock prescaler reset flag (bit 7
at address 008F16) set to “1”
Reset
Clock prescaler
Figure 1.8.6. fc32 block diagram
相关PDF资料
PDF描述
M37481M8-XXXFP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP44
M37481M8T-XXXSP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP42
MB96F356ASAPMC-GE2 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64
MB96F356RWAPMC1-GSE2 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64
MB95F204KP-G-SH-SNE2 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PDIP24
相关代理商/技术参数
参数描述
M30102T-PTC 制造商:Renesas Electronics Corporation 功能描述:DEV 48PIN .5MM QFP CNVTR FOR M30100T-PRB - Bulk
M30-1050046 功能描述:集管和线壳 FML CRIMP CONTACT 1.25MM,AWG 26-30, RL RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector
M30-1060046 功能描述:集管和线壳 FML CRIMP CONTACT 1.25MM,AWG 26-30,LSE RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector
M3010A 制造商:Honeywell Sensing and Control 功能描述:GENERAL MARKET VRS
M3010A25 制造商:Honeywell Sensing and Control 功能描述:GENERAL MARKET VRS
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*