- 您现在的位置：买卖IC网 > PDF目录1837 > MAX16067ETJ+T (Maxim Integrated Products)IC SYSTEM MANAGER 6CH 32-TQFN PDF资料下载
参数资料
| 型号： | MAX16067ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 27/48页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM MANAGER 6CH 32-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 电源监控器，序列发生器 |
| 电源电压： | 2.8 V ~ 14 V |
| 电流 - 电源： | 2.8mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
6-Channel, Flash-Configurable System Manager
with Nonvolatile Fault Registers
Table 22. Reset Output Configuration (continued)
REGISTER
ADDRESS
3Ch
3Dh
FLASH
ADDRESS
23Ch
23Dh
BIT RANGE
[0]
[1]
[2]
[3]
[4]
[5]
[7:6]
[0]
[1]
[2]
[3]
[4]
[5]
[7:6]
DESCRIPTION
1 = RESET depends on MON1 undervoltage
1 = RESET depends on MON2 undervoltage
1 = RESET depends on MON3 undervoltage
1 = RESET depends on MON4 undervoltage
1 = RESET depends on MON5 undervoltage
1 = RESET depends on MON6 undervoltage
Not used
1 = RESET depends on MON1 overvoltage
1 = RESET depends on MON2 overvoltage
1 = RESET depends on MON3 overvoltage
1 = RESET depends on MON4 overvoltage
1 = RESET depends on MON5 overvoltage
1 = RESET depends on MON6 overvoltage
Not used
Watchdog Timer
The watchdog timer operates together with or indepen-
dently of the MAX16067. When operating in dependent
mode, the watchdog is not activated until the sequenc-
ing is complete and RESET is deasserted. When oper-
ating in independent mode, the watchdog timer is
independent of the sequencing operation and activates
immediately after V CC exceeds the UVLO threshold
and the boot phase is complete. Set r73h[4] to ‘0’ to
configure the watchdog in dependent mode. Set r73h[4]
to ‘1’ to configure the watchdog in independent mode.
See Table 23 for more information on configuring the
watchdog timer in dependent or independent mode. The
watchdog timer can be reset by toggling the WDI input
(GPIO4) or by writing a ‘1’ to r75h[5].
Dependent Watchdog Timer Operation
Use the watchdog timer to monitor F P activity in two
modes. Flexible timeout architecture provides an adjust-
able watchdog startup delay of up to 300s, allowing
complicated systems to complete lengthy boot-up rou-
tines. An adjustable watchdog timeout allows the super-
visor to provide quick alerts when the processor activity
fails. After each reset event (V CC drops below UVLO
then returns above UVLO, software reboot, manual reset
( MR ), EN input going low then high, or watchdog reset)
and once sequencing is complete, the watchdog startup
delay provides an extended time for the system to power
up and fully initialize all F P and system components
before assuming responsibility for routine watchdog
updates. Set r76h[6:4] to a value other than ‘000’ to
enable the watchdog startup delay. Set r76h[6:4] to ‘000’
to disable the watchdog startup delay.
The normal watchdog timeout period, t WDI , begins after
the first transition on WDI before the conclusion of the
long startup watchdog period, t WDI_STARTUP (Figures 6
and 7). During the normal operating mode, WDO asserts
if the F P does not toggle WDI with a valid transition (high-
to-low or low-to-high) within the standard timeout period,
t WDI . WDO remains asserted until WDI is toggled or
RESET is asserted (Figure 7).
While EN is low, the watchdog timer is in reset. The
watchdog timer does not begin counting until the power-
on mode is reached and RESET is deasserted. The
watchdog timer is reset and WDO deasserts any time
RESET is asserted (Figure 8). The watchdog timer is
held in reset while RESET is asserted.
The watchdog can be configured to control the RESET
output as well as the WDO output. RESET asserts for
the reset timeout, t RP , when the watchdog timer expires
and the Watchdog Reset Output Enable bit (r76h[7]) is
set to ‘1’. When RESET is asserted, the watchdog timer
is cleared and WDO is deasserted, therefore, WDO
pulses low for a short time (approximately 1 F s) when
______________________________________________________________________________________
27
相关PDF资料 |
PDF描述 |
|---|---|
| MAX16068ETI+T | IC SYSTEM MANAGER 6CH 28-TQFN |
| MAX1606EUA | IC REG BOOST ADJ 0.5A 8UMAX |
| MAX16070ETL+T | IC SYSTEM MANAGER 12CH 40-TQFN |
| MAX16072RS16D0+T | IC MPU SUPERVISOR CIRCUIT 4UCSP |
| MAX1607ESA | IC SW CURRENT LIMITED USB 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16067EVKIT+ | 功能描述:监控电路 6-Channel System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16068ETI+ | 功能描述:监控电路 6Ch System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16068ETI+T | 功能描述:监控电路 6Ch System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16069FTC+ | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16069FTC+T | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。