- 您现在的位置：买卖IC网 > PDF目录1837 > MAX16067ETJ+T (Maxim Integrated Products)IC SYSTEM MANAGER 6CH 32-TQFN PDF资料下载
参数资料
| 型号： | MAX16067ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 31/48页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM MANAGER 6CH 32-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 电源监控器，序列发生器 |
| 电源电压： | 2.8 V ~ 14 V |
| 电流 - 电源： | 2.8mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
6-Channel, Flash-Configurable System Manager
with Nonvolatile Fault Registers
SDA
SDA
SCL
SCL
S
P
DATA LINE STABLE,
DATA VALID
Figure 9. Bit Transfer
CHANGE OF
DATA ALLOWED
START
CONDITION
Figure 10. START and STOP Conditions
STOP
CONDITION
CLOCK PULSE FOR ACKNOWLEDGE
SCL
1
2
8
9
SDA BY
TRANSMITTER
S
NACK
SDA BY
RECEIVER
ACK
Figure 11. Acknowledge
REPEATED START Conditions
A REPEATED START can be sent instead of a STOP
condition to maintain control of the bus during a read
operation. The START and REPEATED START conditions
are functionally identical.
Acknowledge
The acknowledge bit (ACK) is the 9th bit attached to
any 8-bit data word. The receiving device always gener-
ates an ACK. The MAX16067 generates an ACK when
receiving an address or data by pulling SDA low during
the 9th clock period (Figure 11). When transmitting data,
such as when the master device reads data back from
the MAX16067, the device waits for the master device to
generate an ACK. Monitoring ACK allows for detection
of unsuccessful data transfers. An unsuccessful data
transfer occurs if the receiving device is busy or if a sys-
tem fault has occurred. In the event of an unsuccessful
data transfer, the bus master can reattempt communica-
tion at a later time. The MAX16067 generates a NACK
after the command byte received during a software
reboot, while writing to the flash, or when receiving an
illegal memory address.
______________________________________________________________________________________
31
相关PDF资料 |
PDF描述 |
|---|---|
| MAX16068ETI+T | IC SYSTEM MANAGER 6CH 28-TQFN |
| MAX1606EUA | IC REG BOOST ADJ 0.5A 8UMAX |
| MAX16070ETL+T | IC SYSTEM MANAGER 12CH 40-TQFN |
| MAX16072RS16D0+T | IC MPU SUPERVISOR CIRCUIT 4UCSP |
| MAX1607ESA | IC SW CURRENT LIMITED USB 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16067EVKIT+ | 功能描述:监控电路 6-Channel System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16068ETI+ | 功能描述:监控电路 6Ch System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16068ETI+T | 功能描述:监控电路 6Ch System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16069FTC+ | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16069FTC+T | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。