- 您现在的位置：买卖IC网 > PDF目录1837 > MAX16067ETJ+T (Maxim Integrated Products)IC SYSTEM MANAGER 6CH 32-TQFN PDF资料下载
参数资料
| 型号： | MAX16067ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 40/48页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM MANAGER 6CH 32-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 电源监控器，序列发生器 |
| 电源电压： | 2.8 V ~ 14 V |
| 电流 - 电源： | 2.8mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页第48页
6-Channel, Flash-Configurable System Manager
with Nonvolatile Fault Registers
BYPASS: When the BYPASS instruction is latched into
the instruction register, TDI connects to TDO through the
1-bit bypass test data register. This allows data to pass
from TDI to TDO without affecting the device’s operation.
IDCODE: When the IDCODE instruction is latched into
the parallel instruction register, the identification data
register is selected. The device identification code is
loaded into the identification data register on the rising
edge of TCK following entry into the capture-DR state.
Shift-DR can be used to shift the identification code
out serially through TDO. During test-logic-reset, the
IDCODE instruction is forced into the instruction register.
The identification code always has a ‘1’ in the LSB posi-
tion. The next 11 bits identify the manufacturer’s JEDEC
number and number of continuation bytes followed by
16 bits for the device and 4 bits for the version. See
Table 29.
USERCODE: When the USERCODE instruction latches
into the parallel instruction register, the user-code data
register is selected. The device user-code loads into the
user-code data register on the rising edge of TCK fol-
lowing entry into the capture-DR state. Shift-DR can be
used to shift the user-code out serially through TDO. See
Table 30. This instruction can be used to help identify
multiple MAX16067 devices connected in a JTAG chain.
LOAD ADDRESS: This is an extension to the standard
IEEE 1149.1 instruction set to support access to the
Table 29. 32-Bit Identification Code
MSB
memory in the MAX16067. When the LOAD ADDRESS
instruction latches into the instruction register, TDI con-
nects to TDO through the 8-bit memory address test
data register during the shift-DR state.
READ DATA: This is an extension to the standard IEEE
1149.1 instruction set to support access to the memory
in the MAX16067. When the READ DATA instruction
latches into the instruction register, TDI connects to TDO
through the 8-bit memory read test data register during
the shift-DR state.
WRITE DATA: This is an extension to the standard IEEE
1149.1 instruction set to support access to the memory
in the MAX16067. When the WRITE DATA instruction
latches into the instruction register, TDI connects to TDO
through the 8-bit memory write test data register during
the shift-DR state.
REBOOT: This is an extension to the standard IEEE
1149.1 instruction set to initiate a software controlled
reset to the MAX16067. When the REBOOT instruc-
tion latches into the instruction register, the MAX16067
resets and immediately begins the boot-up sequence.
SAVE: This is an extension to the standard IEEE 1149.1
instruction set that triggers a fault log. The current ADC
conversion results along with fault information are saved
to flash depending on the configuration of the Critical
Fault Log Control register (r6Dh).
LSB
VERSION (4 BITS)
0001
PART NUMBER (16 BITS)
1000000000000001
MANUFACTURER (11 BITS)
00011001011
FIXED VALUE (1 BIT)
1
Table 30. 32-Bit User-Code Data
MSB
LSB
DON’T CARE
00000000000000000
See Table 26
SMBUS SLAVE ID
USER ID (r8Ah[7:0])
40
_____________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX16068ETI+T | IC SYSTEM MANAGER 6CH 28-TQFN |
| MAX1606EUA | IC REG BOOST ADJ 0.5A 8UMAX |
| MAX16070ETL+T | IC SYSTEM MANAGER 12CH 40-TQFN |
| MAX16072RS16D0+T | IC MPU SUPERVISOR CIRCUIT 4UCSP |
| MAX1607ESA | IC SW CURRENT LIMITED USB 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16067EVKIT+ | 功能描述:监控电路 6-Channel System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16068ETI+ | 功能描述:监控电路 6Ch System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16068ETI+T | 功能描述:监控电路 6Ch System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16069FTC+ | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16069FTC+T | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。