- 您现在的位置：买卖IC网 > PDF目录1839 > MAX17409GTI+T (Maxim Integrated Products)IC CTRLR NVIDIA CPU 28-TQFN PDF资料下载
参数资料
| 型号： | MAX17409GTI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 28/32页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR NVIDIA CPU 28-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | Quick-PWM™ |
| 应用： | 处理器 |
| 电流 - 电源： | 1.5mA |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页
1-Phase Quick-PWM GPU Controller
I RMS = ? LOAD ? V OUT ( V IN OUT )
In applications that require DC droop, R DROOP(AC) is
the same as the DC droop setting (R DROOP(AC) =
R DROOP(DC) ). In applications that do not require DC
droop, this AC signal is generated by capacitively cou-
pling the inductor ripple current signal to the FB pin. In
this case, R DROOP(AC) = R SENSE , where R SENSE is the
effective sense resistance seen at the CSP-CSN pins.
In Figure 1, C3 couples the inductor ripple current signal
to the FB pin. C3 can be connected to the CSN pin or the
CSP pin. Connecting to the CSN pin only couples the out-
put capacitor ESR to the FB pin. Connecting to the CSP
pin adds the R SENSE component to the effective resis-
tance in addition to the output capacitor ESR. This is use-
ful for applications using all ceramic output capacitors.
Keep the C3 x R FB time constant between 3x and 5x of
the switching period. Practical values for C3 range from
0.1μF to 1μF. Calculate R FB after selecting C3. Keeping
R FB below 100 ? minimizes any residual DC droop.
In the standard application circuit (Figure 1), the effec-
tive resistance for stability is the sum of the ~ 2m ? DCR
and the 6m ? ESR of the 470μF output capacitor. The
ESR zero frequency is 42kHz, well within the require-
ment of f SW / π .
Ceramic capacitors have a high-ESR zero frequency,
but applications with significant voltage positioning can
take advantage of their size and low ESR. Do not put
high-value ceramic capacitors directly across the out-
put without verifying that the circuit contains enough
voltage positioning and series PCB resistance to
ensure stability. When only using ceramic output
capacitors, output overshoot (V SOAR ) typically deter-
mines the minimum output capacitance requirement.
Their relatively low capacitance value can cause output
overshoot when stepping from full-load to no-load con-
ditions, unless a small inductor value is used (high
switching frequency) to minimize the energy transferred
from inductor to capacitor during load-step recovery.
Unstable operation manifests itself in two related but
distinctly different ways: double-pulsing and feedback
loop instability. Double-pulsing occurs due to noise on
the output or because the ESR is so low that there is not
enough voltage ramp in the output-voltage signal. This
“fools” the error comparator into triggering a new cycle
immediately after the minimum off-time period has
expired. Double-pulsing is more annoying than harmful,
resulting in nothing worse than increased output ripple.
However, it can indicate the possible presence of loop
instability due to insufficient ESR. Loop instability can
result in oscillations at the output after line or load
steps. Such perturbations are usually damped, but can
cause the output voltage to rise above or fall below the
tolerance limits.
The easiest method for checking stability is to apply a
very fast zero-to-max load transient and carefully
observe the output-voltage ripple envelope for over-
shoot and ringing. It can help to simultaneously monitor
the inductor current with an AC current probe. Do not
allow more than one cycle of ringing after the initial
step-response under/overshoot.
Input Capacitor Selection
The input capacitor must meet the ripple current
requirement (I RMS ) imposed by the switching currents.
The I RMS requirements can be determined by the fol-
lowing equation:
? I ?
- V
? V IN ?
The worst-case RMS current requirement occurs when
operating with V IN = 2V OUT . At this point, the above
equation simplifies to I RMS = 0.5 x I LOAD .
For most applications, nontantalum chemistries (ceram-
ic, aluminum, or OS-CON) are preferred due to their
resistance to inrush surge currents typical of systems
with a mechanical switch or connector in series with the
input. If the Quick-PWM controller is operated as the
second stage of a two-stage power-conversion system,
tantalum input capacitors are acceptable. In either con-
figuration, choose an input capacitor that exhibits less
than +10 ° C temperature rise at the RMS input current
for optimal circuit longevity.
Power-MOSFET Selection
Most of the following MOSFET guidelines focus on the
challenge of obtaining high load-current capability
when using high-voltage (> 20V) AC adapters. Low-
current applications usually require less attention.
The high-side MOSFET (N H ) must be able to dissipate the
resistive losses plus the switching losses at both V IN(MIN)
and V IN(MAX) . Calculate both of these sums. Ideally, the
losses at V IN(MIN) should be roughly equal to losses at
V IN(MAX) , with lower losses in between. If the losses at
V IN(MIN) are significantly higher than the losses at
V IN(MAX) , consider increasing the size of N H (reducing
R DS(ON) but with higher C GATE ). Conversely, if the losses
at V IN(MAX) are significantly higher than the losses at
V IN(MIN) , consider reducing the size of N H (increasing
R DS(ON) to lower C GATE ). If V IN does not vary over a wide
range, the minimum power dissipation occurs where the
resistive losses equal the switching losses.
Choose a low-side MOSFET that has the lowest possible
on-resistance (R DS(ON) ), comes in a moderate-sized
package (i.e., one or two 8-pin SOs, DPAK, or D 2 PAK),
and is reasonably priced. Make sure that the DL gate
28
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17428GTJ+ | IC PWR SUPPLY CTRLR PWM 32TQFN |
| MAX1744AUB/V+ | IC REG CTRLR BUCK PWM 10-UMAX |
| MAX1747EUP+ | IC CHRG-PUMP TRPL TFTLCD 20TSSOP |
| MAX17480GTL+T | IC CTRLR SERIAL VID 40-TQFN |
| MAX17482GTL+ | IC CTLR PWM DUAL IMVP-6.5 40TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1740EUB | 功能描述:转换 - 电压电平 Integrated Circuits (ICs) RoHS:否 制造商:Micrel 类型:CML/LVDS/LVPECL to LVCMOS/LVTTL 传播延迟时间:1.9 ns 电源电流:14 mA 电源电压-最大:3.6 V 电源电压-最小:3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MLF-8 |
| MAX1740EUB+ | 功能描述:转换 - 电压电平 SIM/Smart Card Level Translator RoHS:否 制造商:Micrel 类型:CML/LVDS/LVPECL to LVCMOS/LVTTL 传播延迟时间:1.9 ns 电源电流:14 mA 电源电压-最大:3.6 V 电源电压-最小:3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MLF-8 |
| MAX1740EUB+T | 功能描述:转换 - 电压电平 SIM/Smart Card Level Translator RoHS:否 制造商:Micrel 类型:CML/LVDS/LVPECL to LVCMOS/LVTTL 传播延迟时间:1.9 ns 电源电流:14 mA 电源电压-最大:3.6 V 电源电压-最小:3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MLF-8 |
| MAX1740EUB-T | 功能描述:转换 - 电压电平 RoHS:否 制造商:Micrel 类型:CML/LVDS/LVPECL to LVCMOS/LVTTL 传播延迟时间:1.9 ns 电源电流:14 mA 电源电压-最大:3.6 V 电源电压-最小:3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MLF-8 |
| MAX17410EVKIT+ | 功能描述:电源管理IC开发工具 MAX17410 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。