- 您现在的位置：买卖IC网 > PDF目录1841 > MAX1897ETP+T (Maxim Integrated Products)IC REG CTRLR BUCK PWM 20-TQFN PDF资料下载
参数资料
| 型号： | MAX1897ETP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 19/33页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 20-TQFN |
| 标准包装： | 2,500 |
| 系列： | Quick-PWM™ |
| PWM 型： | 控制器 |
| 输出数： | 1 |
| 频率 - 最大： | 550kHz |
| 电源电压： | 4.5 V ~ 5.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 85°C |
| 封装/外壳： | 20-WQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Quick-PWM Slave Controllers for
Multiphase, Step-Down Supplies
t ON = K ? COMP ?
I PEAK = I LOAD ( MAX ) ?
2 η ?
?
in MOSFET technology that are making higher frequen-
cies more practical.
Setting Switch On Time: The constant on-time control
algorithm in the master results in a nearly constant
switching frequency despite the lack of a fixed-frequen-
cy clock generator. In the slave, the high-side switch on
time is inversely proportional to V+ and directly propor-
tional to the compensation voltage (V COMP ):
? V ?
? V IN ?
where K is internally preset to 3.3μs for the MAX1887 or
externally set by the TON pin-strap connection for the
MAX1897 (Table 3)
Set the nominal on time in the slave to match the on
time in the master. An exact match is not necessary
because the MAX1887/MAX1897 have wide t ON adjust-
ment ranges (±40%). For example, if t ON in the master
is set to 250kHz, the slave can be set to either 200kHz
or 300kHz and still achieve good performance. Care
Find a low-loss inductor having the lowest possible DC
resistance that fits in the allotted dimensions. Ferrite
cores are often the best choice, although powdered
iron is inexpensive and can work well at 200kHz. The
core must be large enough not to saturate at the peak
inductor current (I PEAK ):
? 2 + LIR ?
?
where η is the number of phases.
Transient Response
The inductor ripple current affects transient-response
performance, especially at low V IN - V OUT differentials.
Low inductor values allow the inductor current to slew
faster, replenishing charge removed from the output fil-
ter capacitors by a sudden load step. The amount of
output sag also is a function of the maximum duty fac-
tor, which can be calculated from the on time and mini-
mum off time:
(
)
L ? I LOAD ( MAX ) 2 ? ? OUT ? + t OFF ( MIN ) ?
? ? ?
? ?
? ? ( V IN OUT ) K ?
2 η C OUT OUT ? ? ? ? t OFF ( MIN ) ?
? ? ? ?
should be taken to ensure that the COMP voltage
remains within its output voltage range (0.42V to
2.80V).
Inductor Operating Point: This choice provides trade-
offs between size vs. efficiency and transient response
vs. output noise. Low inductor values provide better
transient response and smaller physical size, but also
V SAG =
V
? ? V K ? ?
V IN ?
V IN
? V ?
( ? I LOAD ( MAX ) )
2 η C OUT OUT
result in lower efficiency and higher output noise due to
increased ripple current. The minimum practical induc-
tor value is one that causes the circuit to operate at the
edge of critical conduction (where the inductor current
just touches zero with every cycle at maximum load).
Inductor values lower than this grant no further size-
reduction benefit. The optimum operating point is usu-
ally found between 20% and 50% ripple current.
Inductor Selection
The switching frequency and operating point (% ripple
or LIR) determine the inductor value as follows:
where t OFF(MIN) is the minimum off time (see the
Electrical Characteristics section), η is the number of
phases, and K is from Table 3.
The amount of overshoot due to stored inductor energy
can be calculated as:
2
L
V SOAR ≈
V
Setting the Current Limits
The master and slave current-limit thresholds must be
L =
V OUT x ( V IN ? V OUT ) x η
V IN xf SW xI LOAD ( MAX ) xLIR
great enough to support the maximum load current,
even under worst-case operating conditions. Since the
master ’ s current limit determines the maximum load
(see the Current-Limit Circuitry section), the procedure
where η is the number of phases. Example: η = 2,
I LOAD = 40A, V IN = 12V, V OUT = 1.3V, f SW = 300kHz,
30% ripple current or LIR = 0.3:
for setting the current limit is sequential. First, the mas-
ter ’ s current limit is set based on the operating condi-
tions and the characteristics of the low-side MOSFETs.
L =
1 . 3 V x ( 12 V ? 1 . 3 V ) x 2
12 V x 300 kHz x 40 A x 0 . 3
= 0 . 64 μ H
Then the slave controller is configured to adjust the
master ’ s current-limit threshold based on the precise
current-sense resistor value and variation in the MOS-
FET characteristics. Finally, the resulting valley current
limit for the slave ’ s inductor occurs above the master ’ s
______________________________________________________________________________________
19
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1898EUB42+T | IC CHARGER LI+ SNGL 10-UMAX |
| MAX1904ETJ+ | IC CNTRLR PWR SPLY LN 32-TQFN |
| MAX1917EEE+T | IC CNTRLR SYNC BUCK 16-QSOP |
| MAX1921EUT33+T | IC REG BUCK SYNC 3.3V SOT23-6 |
| MAX1922ESA+ | IC SW CUR LIMIT USB 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1898EUB41 | 功能描述:电池管理 Linear Charger for 1-Cell Li+ Battery RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1898EUB41+ | 功能描述:电池管理 Linear Charger for 1-Cell Li+ Battery RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1898EUB41+T | 功能描述:电池管理 Linear Charger for 1-Cell Li+ Battery RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1898EUB41-T | 功能描述:电池管理 Linear Charger for 1-Cell Li+ Battery RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1898EUB42 | 功能描述:电池管理 Linear Charger for 1-Cell Li+ Battery RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。