- 您现在的位置：买卖IC网 > PDF目录1841 > MAX1897ETP+T (Maxim Integrated Products)IC REG CTRLR BUCK PWM 20-TQFN PDF资料下载
参数资料
| 型号： | MAX1897ETP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 25/33页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 20-TQFN |
| 标准包装： | 2,500 |
| 系列： | Quick-PWM™ |
| PWM 型： | 控制器 |
| 输出数： | 1 |
| 频率 - 最大： | 550kHz |
| 电源电压： | 4.5 V ~ 5.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 85°C |
| 封装/外壳： | 20-WQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页
Quick-PWM Slave Controllers for
Multiphase, Step-Down Supplies
? ? ? I
?
? V
LOAD ? R
PD ( N L Re sistive ) = ? 1 ? ? ? ? ?
?
η
? V IN ( MAX ) ? ? ? ?
?
? ?
I LOAD = η I VALLEY ( MAX ) + ? ?
? ?
V IN(MAX) , consider choosing another MOSFET with
lower parasitic capacitance.
For the low-side MOSFET (N L ), the worst-case power
dissipation always occurs at maximum input voltage:
2
OUT
DS ( ON )
The worst case for MOSFET power dissipation occurs
under heavy overloads that are greater than
I LOAD(MAX) but are not quite high enough to exceed
the current limit and cause the fault latch to trip. To pro-
tect against this possibility, “ overdesign ” the circuit to
tolerate:
? I LOAD(MAX) LIR ?
2
where I VALLEY(MAX) is the maximum valley current
allowed by the current-limit circuit, including threshold
tolerance and on-resistance variation. The MOSFETs
must have a good-sized heatsink to handle the over-
load power dissipation.
Choose a Schottky diode (D1) with a forward voltage
low enough to prevent the low-side MOSFET body
diode from turning on during the dead time. As a gen-
eral rule, select a diode with a DC current rating equal
to 1/(3 η ) of the load current. This diode is optional and
can be removed if efficiency is not critical.
Current Balance Compensation (COMP)
The current balance compensation capacitor (C COMP )
integrates the difference of the master and slave cur-
rent-sense signals, while the compensation resistor
improves transient response by increasing the phase
margin. This allows the user to optimize the dynamics
of the current balance loop. Excessively large capacitor
values increase the integration time constant, resulting
in larger current differences between the phases during
transients. Excessively small capacitor values allow the
current loop to respond cycle by cycle but can result in
small DC current variations between the phases.
Likewise, excessively large series resistance can also
cause DC current variations between the phases. Small
series resistance reduces the phase margin, resulting
in marginal stability in the current balance loop. For
most applications, a 470pF capacitor and 10k ? series
resistor from COMP to the converter ’ s output voltage
works well.
The compensation network can be tied to V OUT to
include the feed-forward term due to the master ’ s on
time (see the On-time Control and Active Current
Balancing section). To reduce noise pick-up in applica-
tions that have a widely distributed layout, it is some-
times helpful to connect the compensation network to
quiet analog ground rather than V OUT .
Applications Information
Voltage Positioning and
Effective Efficiency
Powering new mobile processors requires careful
attention to detail to reduce cost, size, and power dissi-
pation. As CPUs became more power hungry, it was
recognized that even the fastest DC-DC converters
were inadequate to handle the transient power require-
ments. After a load transient, the output instantly
changes by ESR COUT ? ? I LOAD . Conventional DC-DC
converters respond by regulating the output voltage
back to its nominal state after the load transient occurs
(Figure 7). However, the CPU only requires that the out-
put voltage remain above a specified minimum value.
Dynamically positioning the output voltage to this lower
limit allows the use of fewer output capacitors and
reduces power consumption under load.
For a conventional (nonvoltage-positioned) circuit, the
total voltage change is:
V P-P 1 = 2 ? (ESR COUT ? ? I LOAD ) + V SAG + V SOAR
where V SAG and V SOAR are defined in Figure 8. Setting
the converter to regulate at a lower voltage when under
load allows a larger voltage step when the output cur-
rent suddenly decreases (Figure 7). So the total voltage
change for a voltage-positioned circuit is:
V P-P 2 = (ESR COUT ? ? I LOAD ) + V SAG + V SOAR
where V SAG and V SOAR are defined in the Design
Procedure section. Since the amplitudes are the same
for both circuits (V P-P 1 = V P-P 2), the voltage-positioned
circuit tolerates twice the ESR. Since the ESR specifica-
tion is achieved by paralleling several capacitors, fewer
units are needed for the voltage-positioned circuit.
An additional benefit of voltage positioning is reduced
power consumption at high load currents. Since the
output voltage is lower under load, the CPU draws less
current. The result is lower power dissipation in the
CPU, although some extra power is dissipated in
R SENSE . For a nominal 1.6V, 22A output (R LOAD =
72.7m ? ), reducing the output voltage 2.9% gives an
output voltage of 1.55V and an output current of 21.3A.
Given these values, CPU power consumption is
reduced from 35.2W to 33.03W. The additional power
consumption of R SENSE is:
______________________________________________________________________________________
25
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1898EUB42+T | IC CHARGER LI+ SNGL 10-UMAX |
| MAX1904ETJ+ | IC CNTRLR PWR SPLY LN 32-TQFN |
| MAX1917EEE+T | IC CNTRLR SYNC BUCK 16-QSOP |
| MAX1921EUT33+T | IC REG BUCK SYNC 3.3V SOT23-6 |
| MAX1922ESA+ | IC SW CUR LIMIT USB 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1898EUB41 | 功能描述:电池管理 Linear Charger for 1-Cell Li+ Battery RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1898EUB41+ | 功能描述:电池管理 Linear Charger for 1-Cell Li+ Battery RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1898EUB41+T | 功能描述:电池管理 Linear Charger for 1-Cell Li+ Battery RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1898EUB41-T | 功能描述:电池管理 Linear Charger for 1-Cell Li+ Battery RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1898EUB42 | 功能描述:电池管理 Linear Charger for 1-Cell Li+ Battery RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。