- 您现在的位置：买卖IC网 > PDF目录1849 > MAX8792ETD+T (Maxim Integrated Products)IC PWM CTRLR STEP-DWN 14TDFN PDF资料下载
参数资料
| 型号： | MAX8792ETD+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/28页 |
| 文件大小： | 0K |
| 描述： | IC PWM CTRLR STEP-DWN 14TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 应用： | PWM 控制器 |
| 输入电压： | 2 V ~ 26 V |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 700µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-WFDFN 裸露焊盘 |
| 供应商设备封装： | 14-TDFN-EP（3x3） |
| 包装： | 标准包装 |
| 其它名称： | MAX8792ETD+TDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Single Quick-PWM Step-Down
Controller with Dynamic REFIN
Slowly discharging the output capacitors by slewing
the output over a long period of time (typically 0.5ms to
2ms) keeps the average negative inductor current low
(damped response), thereby preventing the negative
output-voltage excursion that occurs when the con-
troller discharges the output quickly by permanently
turning on the low-side MOSFET (underdamped
response). This eliminates the need for the Schottky
diode normally connected between the output and
ground to clamp the negative output-voltage excursion.
After the controller reaches the zero target, the
MAX8792 shuts down completely—the drivers are dis-
abled (DL and DH pulled low)—the reference turns off,
and the supply currents drop to about 0.1μA (typ).
When a fault condition—output UVP or thermal shut-
down—activates the shutdown sequence, the protection
circuitry sets the fault latch to prevent the controller from
restarting. To clear the fault latch and reactivate the
controller, toggle EN or cycle V CC power below 0.5V.
The MAX8792 automatically uses pulse-skipping mode
during soft-start and uses forced-PWM mode during
soft-shutdown, regardless of the SKIP configuration.
Modes of Operation
Forced-PWM Mode ( S K I P = V DD )
The low-noise, forced-PWM mode ( SKIP = V DD ) dis-
ables the zero-crossing comparator, which controls the
low-side switch on-time. This forces the low-side gate-
drive waveform to constantly be the complement of the
high-side gate-drive waveform, so the inductor current
reverses at light loads while DH maintains a duty factor
of V OUT /V IN . The benefit of forced-PWM mode is to
keep the switching frequency fairly constant. However,
forced-PWM operation comes at a cost: the no-load 5V
bias current remains between 10mA to 50mA, depend-
ing on the switching frequency.
The MAX8792 automatically always uses forced-PWM
operation during shutdown, regardless of the SKIP
configuration.
Automatic Pulse-Skipping Mode
( S K I P = GND or 2V)
In skip mode ( SKIP = GND or 2V), an inherent automat-
ic switchover to PFM takes place at light loads. This
switchover is affected by a comparator that truncates
the low-side switch on-time at the inductor current’s
is higher than the trip level by 50% of the output ripple
voltage. In discontinuous conduction ( SKIP = GND and
I OUT < I LOAD(SKIP) ), the output voltage has a DC regu-
lation level higher than the error-comparator threshold
by approximately 1.5% due to slope compensation.
When SKIP is pulled to GND, the MAX8792 remains in
pulse-skipping mode. Since the output is not able to
sink current, the timing for negative dynamic output-volt-
age transitions depends on the load current and output
capacitance. Letting the output voltage drift down is typ-
ically recommended in order to reduce the potential for
audible noise since this eliminates the input current
surge during negative output-voltage transitions.
Ultrasonic Mode ( S K I P = Open = 3.3V)
Leaving SKIP unconnected activates a unique pulse-
skipping mode with a minimum switching frequency of
18kHz. This ultrasonic pulse-skipping mode eliminates
audio-frequency modulation that would otherwise be
present when a lightly loaded controller automatically
skips pulses. In ultrasonic mode, the controller automati-
cally transitions to fixed-frequency PWM operation when
the load reaches the same critical conduction point
(I LOAD(SKIP) ) that occurs when normally pulse skipping.
An ultrasonic pulse occurs when the controller detects
that no switching has occurred within the last 33μs.
Once triggered, the ultrasonic controller pulls DL high,
turning on the low-side MOSFET to induce a negative
inductor current (Figure 3). After the inductor current
reaches the negative ultrasonic current threshold, the
controller turns off the low-side MOSFET (DL pulled low)
33 μ s (typ)
INDUCTOR
CURRENT
ZERO-CROSSING
DETECTION
0
zero crossing. The zero-crossing comparator threshold
is set by the differential across LX to GND.
DC output-accuracy specifications refer to the thresh-
old of the error comparator. When the inductor is in
continuous conduction, the MAX8792 regulates the val-
ley of the output ripple, so the actual DC output voltage
I SONIC
Figure 3. Ultrasonic Waveform
ON-TIME (t ON )
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8794ETB+T | IC DDR LINEAR REG 10-TDFN |
| MAX8795AETJ+C7P | IC TFT-LCD DC/DC CONV 32-TQFN |
| MAX8798ETX+T | IC INTERNAL-SW BOOST REG 36-TQFN |
| MAX8804VETA+T | IC USB/AC ADP CHARGER 8TDFN-EP |
| MAX8804YETA+T | IC USB/AC ADP CHARGER 8-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8792EVKIT+ | 功能描述:电源管理IC开发工具 MAX8792 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8794ETB/V+T | 功能描述:低压差稳压器 - LDO Low-Voltage DDR Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8794ETB+ | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE DDR LINEAR REGULATOR - Rail/Tube |
| MAX8794ETB+T | 功能描述:低压差稳压器 - LDO Low-Voltage DDR Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8795AETJ+ | 功能描述:直流/直流开关转换器 TFT-LCD DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。