- 您现在的位置：买卖IC网 > PDF目录1851 > MC33984BPNAR2 (Freescale Semiconductor)IC SWITCH HI SIDE DUAL 16-PQFN PDF资料下载
参数资料
| 型号： | MC33984BPNAR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 17/39页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH HI SIDE DUAL 16-PQFN |
| 标准包装： | 1,200 |
| 类型： | 高端 |
| 输入类型： | SPI |
| 输出数： | 2 |
| 导通状态电阻： | 4 毫欧 |
| 电源电压： | 6 V ~ 27 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-PowerDFN |
| 供应商设备封装： | 16-PQFN（12x12） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 33984 is a dual self-protected 4.0 m ? silicon switch
used to replace electromechanical relays, fuses, and discrete
devices in power management applications. The 33984 is
designed for harsh environments, and it includes self-
recovery features. The device is suitable for loads with high
inrush current, as well as motors and all types of resistive and
inductive loads.
Programming, control, and diagnostics are implemented
via the Serial Peripheral Interface (SPI). A dedicated parallel
input is available for alternate and Pulse Width Modulation
(PWM) control of each output. SPI-programmable fault trip
thresholds allow the device to be adjusted for optimal
performance in the application.
The 33984 is packaged in a power-enhanced 12 x 12
nonleaded PQFN package with exposed tabs.
FUNCTIONAL PIN DESCRIPTION
OUTPUT CURRENT MONITORING (CSNS)
This pin is used to output a current proportional to the
designated HS0-1 output. That current is fed into a ground-
referenced resistor and its voltage is monitored by an MCU's
A/D. The channel to be monitored is selected via the SPI.
This pin can be tri-stated through the SPI.
WAKE (WAKE)
This pin is used to input a Logic [1] signal so as to enable
the watchdog timer function. An internal clamp protects this
pin from high damaging voltages when the output is current
limited with an external resistor. This input has a passive
internal pull-down.
RESET (RST)
This input pin is used to initialize the device configuration
and fault registers, as well as place the device in a low-
current Sleep mode. The pin also starts the watchdog timer
when transitioning from Logic LOW to Logic HIGH. This pin
should not be allowed to be Logic HIGH until V DD is in
regulation. This pin has a passive internal pull-down.
DIRECT IN 0 & 1 (INx)
This input pin is used to directly control the output HS0 and
1. This input has an active internal pull-down current source
and requires CMOS logic levels. This input may be
configured via the SPI.
FAULT STATUS (FS)
This is an open drain configured output requiring an
external pull-up resistor to V DD for fault reporting. When a
device fault condition is detected, this pin is active LOW.
Specific device diagnostic faults are reported via the SPI SO
pin.
FAIL-SAFE INPUT (FSI)
The value of the resistance connected between this pin
and ground determines the state of the outputs after a
watchdog timeout occurs. Depending on the resistance
value, either all outputs are OFF, ON, or the output HS0 only
is ON. When the FSI pin is connected to GND, the watchdog
circuit and fail-safe operation are disabled. This pin
incorporates an active internal pull-up current source.
CHIP SELECT (CS)
This input pin is connected to a chip select output of a
master microcontroller (MCU). The MCU determines which
device is addressed (selected) to receive data by pulling the
CS pin of the selected device Logic LOW, enabling SPI
communication with the device. Other unselected devices on
the serial link having their CS pins pulled-up Logic HIGH
disregard the SPI communication data sent. This pin
incorporates an active internal pull-up current source.
SERIAL CLOCK (SCLK)
This input pin is connected to the MCU providing the
required bit shift clock for SPI communication. It transitions
one time per bit transferred at an operating frequency, f SPI ,
defined by the communication interface. The 50 percent duty
cycle CMOS-level serial clock signal is idle between
command transfers. The signal is used to shift data into and
out of the device. This input has an active internal pull-down
current source.
SERIAL INPUT (SI)
This is a command data input pin connected to the SPI
Serial Data Output of the MCU or to the SO pin of the
previous device of a daisy chain of devices. The input
requires CMOS logic-level signals and incorporates an active
internal pull-down current source. Device control is facilitated
by the input's receiving the MSB first of a serial 8-bit control
command. The MCU ensures data is available upon the
falling edge of SCLK. The logic state of SI present upon the
rising edge of SCLK loads that bit command into the internal
command shift register.
DIGITAL DRAIN VOLTAGE (VDD)
This is an external voltage input pin used to supply power
to the SPI circuit. In the event V DD is lost, an internal supply
provides power to a portion of the logic, ensuring limited
functionality of the device. All device configuration registers
are reset.
33984
Analog Integrated Circuit Device Data ?
Freescale Semiconductor
17
相关PDF资料 |
PDF描述 |
|---|---|
| MC33988CPNA | IC SWITCH HIGH SIDE DUAL 16QFN |
| MC33997DW | IC SWITCH 3.3/5V SUPPLY 24-SOIC |
| MC34063AD | IC REG BUCK BOOST INV 1.5A 8SOP |
| MC34063AMELG | IC REG BUCK BST INV ADJ 8SOEIAJ |
| MC34063AP | IC REG BUCK BOOST INV 1.5A 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33984CHFK | 功能描述:电源开关 IC - 配电 Dual 4mOhms smart RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33984CHFKR2 | 功能描述:电源开关 IC - 配电 Dual 4mOhms smart RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33984PNA | 制造商:Freescale Semiconductor 功能描述:POWER SWITCH HI SIDE 30A 16-PIN QFN - Trays |
| MC33984PNAR2 | 制造商:Freescale Semiconductor 功能描述:DUAL INTELLIGENT HIGH-CURRENT SELF-PROTECTED SILICON SWITCH - Tape and Reel |
| MC33988CHFK | 功能描述:电源开关 IC - 配电 DUAL 8MOHMS SMART RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
发布紧急采购，3分钟左右您将得到回复。