- 您现在的位置：买卖IC网 > PDF目录16586 > MC34921AE (Freescale Semiconductor)IC MOTOR DRVR PWM DC DUAL 64LQFP PDF资料下载
参数资料
| 型号： | MC34921AE |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 22/36页 |
| 文件大小： | 0K |
| 描述： | IC MOTOR DRVR PWM DC DUAL 64LQFP |
| 标准包装： | 800 |
| 应用： | DC 电机驱动器，步进电机驱动器，H 桥式 |
| 输出数： | 2 |
| 电流 - 输出： | ±4.5A |
| 电压 - 负载： | 0 V ~ 38 V |
| 电源电压： | 4.8 V ~ 5.2 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP 裸露焊盘 |
| 供应商设备封装： | 64-LQFP EP（10x10） |
| 包装： | 散装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
The power up sequence of the 5.0 V and 3.3 V switching
regulators is controlled such that -1.0v <= V5 - V3.3 <= 2.6v.
Figure 10 depicts the power-up sequence for the 5.0 V and
3.3 V regulators.
external regulator is then connected to the VCORE terminal
for under-voltage monitoring.
Table 5. V CORE Regulator Output Voltage Select
V 5.0 < V 5_3.3 t
Power-Up
V CORE SELECT
Tied to Ground terminal
V CORE_NOM
(Volts)
1.5
V 5.0 ≥ V 5_3.3t
5.0 V Reg ON
Ref = 2.5 V
3.3 V Reg OFF
5.0 V ≥ 3.3 V
Undervoltage (UV)
Tied to 3.3V terminal
Floating
1.8
2.5
3.3 V ≠ Positive
Threshold
DC MOTOR DRIVERS
3.3 V Start
3.3 V Reg ON
Ref = 2.5 V
5.0 V Reg ON
5.0 V Fault
5.0 V Reg ON
3.3 V Reg OFF
V 5.0 ≥ V 5_3.3t
& 3.3 V > 3.3 V UV
There are two DC motor drivers on the 34921 IC: if used in
a printer application, for example, they might be the carriage
motor driver and the paper motor driver. A third drive, Motor
Driver C, can be configured as a DC motor driver or, when
B+ NOM = 18 V, as a step motor driver (refer to succeeding
paragraph Step Motor Driver ). Configuration bit 13
3.3 V ≥ Positive
Threshold
Full Start
Ref = 5.0 V
3.3 V Reg ON
5.0 V Reg ON
V 5.0 ≤ V 5_3.3t
determines the mode: 0 = step mode, 1 = DC mode. A step
motor driver can only be used in B+ = 12 V to 20 V
applications. Step motor outputs are suppressed by the
internal supervisor for B+ > 20 V. The ability to use the low-
side MOSFETs for general purpose low-side outputs is
included when the system is in DC motor mode (LSOUTx).
Figure 10. Power-Up Sequencing
VCORE LINEAR REGULATOR
The output voltage of the VCORE linear regulator is
selectable for different applications. The output is selected
with an external pull-up or pull-down, which instructs internal
logic to select the appropriate regulator set-point (refer to
the 3.3 V supply is in stable operation.
Current limiting is implemented to provide short circuit
protection. The VCORE linear regulator is shut off by the local
thermal shutdown sensor, thus protecting the 34921 IC from
an over-temperature condition resulting from a VCORE short
circuit, but otherwise allowing VCORE to follow the 3.3 V
switching regulator.
The VCORE SUPPLY terminal is the drain or collector of
the linear regulator transistor and must be tied to the 3.3V
terminal to use the internal regulator. This allows the option
of using an external regulator if the internal 3.3 V regulator
cannot supply enough current for a particular application.
Use of an external regulator requires leaving this terminal
open, thus disabling the internal regulator. The output of the
Alternatively, the ability to use the high-side MOSFETs for
general purpose high-side outputs (HSOUTx) has been
included when the system is in step mode. (Refer to
The DC motor drivers are pulse width modulated (PWM’d)
via inputs from the digital subsystem on the APWM and
BPWM terminals, respectively. This signal is approximately
20 kHz to 40 kHz. The DC motor driver bridge direction may
be reversed while there is significant current flowing in the
motor. The purpose of this action is to brake the motor by
rapidly lowering the current. There are pull-downs on the
PWM input terminals so that, in the event of a connection
failure, the driver will default to a safe condition.
The DC motor drivers provide high-side and low-side
current limiting. The current limits have a 0.5 μ s to 6.0 μ s
deglitch filter, followed by an off-timer. The off-timer shuts off
the bridge long enough to meet the 4% duty cycle goal. The
motor drivers also have thermal shutdown protection.
STEP MOTOR DRIVER C
Step motor driver C can be configured as a DC motor
driver or, when B+ NOM = 18 V, as a step motor driver (refer to
succeeding paragraph Step Motor Driver ). Configuration
bit 13 determines the mode: 0 = step mode, 1 = DC mode.
The ability to use the low-side MOSFETs for general purpose
low-side outputs is included when the system is in DC motor
mode (LSOUTx). Alternatively, the ability to use the high-side
MOSFETs for general purpose high-side outputs (HSOUTx)
has been included when the system is in step mode. (Refer
to Table 20 , page 31 , and Table 21 , page 32 .)
34921
Analog Integrated Circuit Device Data
22
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| EBM18DSAS | CONN EDGECARD 36POS R/A .156 SLD |
| M3UUK-1006R | IDC CABLE - MKS10K/MC10M/MKS10K |
| 1-830126-3 | CONN LEAD ASSY DBL END 16AWG |
| V300C12E150BF2 | CONVERTER MOD DC/DC 12V 150W |
| H3BWH-4006M | IDC CABLE - HSR40H/AE40M/HPL40H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC34921AER2 | 功能描述:马达/运动/点火控制器和驱动器 DUAL PWM DC MOTOR DRIVE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC34923 | 制造商:SPC Multicomp 功能描述:HEADER VERTICAL 3WAY 制造商:SPC Multicomp 功能描述:HEADER, VERTICAL, 3WAY 制造商:SPC Multicomp 功能描述:WIRE-BOARD CONNECTOR, RCPT, 3POS, 4.2MM; Series:2266(5566)RA; Pitch Spacing:4.2mm; Contact Termination:Through Hole Vertical; No. of Contacts:3; No. of Rows:1; Connector Mounting:PCB; Gender:Receptacle; Contact Material:Brass ;RoHS Compliant: Yes |
| MC34923DW | 功能描述:马达/运动/点火控制器和驱动器 Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC34923EG | 功能描述:马达/运动/点火控制器和驱动器 Full-Bridge PWM Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC34923EGR2 | 功能描述:马达/运动/点火控制器和驱动器 VERSION RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。