- 您现在的位置：买卖IC网 > PDF目录11749 > MCZ33781EK (Freescale Semiconductor)IC MASTER DSI 2.02 DIFF 32-SOIC PDF资料下载
参数资料
| 型号： | MCZ33781EK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 11/44页 |
| 文件大小： | 0K |
| 描述： | IC MASTER DSI 2.02 DIFF 32-SOIC |
| 标准包装： | 42 |
| 应用： | 车载系统 |
| 接口： | SPI |
| 电源电压： | 4.75 V ~ 5.25 V |
| 封装/外壳： | 32-BSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 32-SOICW 裸露焊盘 |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
33781
FUNCTIONAL DESCRIPTIONS
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
the driver. The over-voltage input causes the driver
characteristics to be modified under over-voltage conditions.
This is described in more detail in the Load Dump Operation
section.
A special requirement of the differential bus is to maintain
a low common mode voltage. This is accomplished by
monitoring the common mode voltage and modifying the
driver slew rates. This is the function of the Common Mode
Correction
block.
Current signals sent by the slave are detected on both the
high side and the low side of the bus using a differential
current sense architecture. Sense resistors between the
Signal driver and the DnH and DnL outputs detect the slave
device response current. Sensing the current on both bus
lines improves the fault diagnostics of the bus. Also included
is an adder circuit which is used to improve the reception of
sensor data in the presence of common mode noise. The
comparators in the blocks output a high or low value
depending on if the input is above or below the signal
threshold.
The Receiver High, Receiver Low, and Receiver Sum
outputs are sent to the device logic block which is shown in
Figure 23. The data is sampled at the falling edge of DSIS. In
the presence of faults or common mode noise it is possible
that all three receiver circuits will not produce the same bit
pattern. To check for this, each of the three receiver filter
outputs is passed to a CRC generation and checking block.
A logic block determines which (if any) of the receiver filter
blocks has produced the correct result, by comparing the
CRC results along with the bit-by-bit XOR of the high side and
low side bit pattern. Table 7 shows how the logic determines
which (if any) receiver outputs contain a valid response. The
data is selected from either the Receiver High, Receiver Low
or Receiver Sum circuit and the ER bit is set accordingly in
the DnRnSTAT register.
If either Receiver High or Receiver Low has all 1’s for data,
including the CRC bits, then the ER bit will be set. For either
of these two conditions, the ER bit will be set regardless of
the Receiver Sum data value and regardless of whether or
not all the 1’s caused a CRC error on the High or Low side.
Note that SPI0 and SPI1 do not use the same sources for
their respective output data streams. SPI0 chooses between
Receiver High or Receiver Sum0; SPI1 chooses between
Receiver Low and Receiver Sum1.
In order to provide the maximum protection against a
single-point failure causing a disruption in communication,
the decision paths for the two SPI channels are internally
independent . For example, Receiver Sum0 and Receiver
Sum1 use different holding registers in the Receiver logic.
These registers are duplicates, although they will always hold
the same data unless there is a fault in one of the data paths.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27484E14B18PB | CONN PLUG 18POS STRAIGHT W/PINS |
| PIC18LF4221-I/ML | IC PIC MCU FLASH 2KX16 44QFN |
| VE-B4D-IX-F3 | CONVERTER MOD DC/DC 85V 75W |
| UPL2000-D19 | BNC PLUG CRIMP STR BELDEN 1855A |
| UPL2000-D1 | BNC PLUG CRIMP STR 7538 CABLE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33781EKR2 | 功能描述:输入/输出控制器接口集成电路 DBUS2 MASTER STND RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| MCZ33784EF | 功能描述:加速计 - 板上安装 DBUS2 SENSOR INTERFACE RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| MCZ33784EF/R2- | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:DSI 2.02 Sensor Interface |
| MCZ33784EFR2 | 功能描述:加速计 - 板上安装 DBUS2 SENSOR INTERFACE RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| MCZ33789AE | 功能描述:网络控制器与处理器 IC Airbag ASSP RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。