- 您现在的位置：买卖IC网 > PDF目录11749 > MCZ33781EK (Freescale Semiconductor)IC MASTER DSI 2.02 DIFF 32-SOIC PDF资料下载
参数资料
| 型号： | MCZ33781EK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 26/44页 |
| 文件大小： | 0K |
| 描述： | IC MASTER DSI 2.02 DIFF 32-SOIC |
| 标准包装： | 42 |
| 应用： | 车载系统 |
| 接口： | SPI |
| 电源电压： | 4.75 V ~ 5.25 V |
| 封装/外壳： | 32-BSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 32-SOICW 裸露焊盘 |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
Analog Integrated Circuit Device Data
32
Freescale Semiconductor
33781
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
DnRnH REGISTERS
These are read/write registers. There are sixteen of these
registers, four for each of the buses, as shown in Table 8.
When written to, the data is the high byte of a 9- to16-bit
command. When read, it is the high byte of a 9- to 16-bit
return on the DBUS. Writing to this register and the low byte
register without a framing error schedules a DBUS
transaction.
The bit assignments are shown in Figure 24. Even if a
short word of 8 bits is selected for this bus (MSn = 1), this
register must be written in the SPI burst sequence. When the
short word length is set at other than 8 bits, this register will
contain the bits above eight, starting with the ninth bit in the
least significant bit position of the register. Unused bit
positions are don’t care values.
Figure 24. DnRnH Data Register Bit Assignments
DnRnL REGISTERS
These are read/write registers. There are sixteen of these
registers, four for each of the buses. When written to, the data
is the low byte of a 16-bit command. When in read, it is the
low byte of a 16-bit return on the DBUS. Writing to this
register and the high byte register without a framing error,
schedules a DBUS transaction. The bit assignments are
shown in Figure 25
If this address is pointed to by the first SPI0 byte of a SPI
burst transaction, that transaction is ignored.
Figure 25. DnRnL Data Register Bit Assignments
DnRnSTAT REGISTER
There are read-only registers. These registers cover the
status of their associated DnRnH and DnRnl registers. The
values are latched when CS0 is asserted low. Any changes of
status detected by these bits will not update the register until
CS0
is de-asserted. This is done to ensure that partial
updates will not occur. If this address is pointed to by the first
SPI0 byte of a SPI burst transaction, that transaction is
ignored.
The bit assignments are shown in Figure 26.
Figure 26. DnRnSTAT Register Bit Assignments
ER–CRC Error Bit
0 = CRC value for the data in the read buffer was
correct.
1 = CRC value for the data in the read buffer was not
correct (data not valid).
CRC errors are associated with each receive buffer, so
that each buffer has a bit to indicate whether the data in that
buffer was received correctly. Whenever a received data
value is available in the DnRnH and DnRnL registers, the
associated CRC error status is available at ERn in the
associated DnRnSTAT register. The ER bit is set or cleared
whenever data is written from the DBUS into the DnRnH/L
receive registers. If Channel Thermal Shutdown or Idle and
SIgnal Mode Disable occur, these bits will be reset along with
the other channel register bits.
TE–Transmit Register Empty Bit
0 = Transmit buffer not empty.
1 = Transmit buffer empty.
This bit indicates that data has been written to the
associated channel register high and/or low, but has not been
read for sending on the DBUS. The bit is set to 0 on the rising
SPI Data Bit
Bit 7
6
5
4
3
2
1
0
Read/Write
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Reset
0
SPI Data Bit
Bit 7
6
5
4
3
2
1
0
Read/Write
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
0
SPI Data Bit
Bit 7
6
5
4
3
2
1
0
Read
ER
TE
SDS
RNE
ICL
0
FIX0
FIX1
Reset
0
1
0
1
相关PDF资料 |
PDF描述 |
|---|---|
| MS27484E14B18PB | CONN PLUG 18POS STRAIGHT W/PINS |
| PIC18LF4221-I/ML | IC PIC MCU FLASH 2KX16 44QFN |
| VE-B4D-IX-F3 | CONVERTER MOD DC/DC 85V 75W |
| UPL2000-D19 | BNC PLUG CRIMP STR BELDEN 1855A |
| UPL2000-D1 | BNC PLUG CRIMP STR 7538 CABLE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33781EKR2 | 功能描述:输入/输出控制器接口集成电路 DBUS2 MASTER STND RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| MCZ33784EF | 功能描述:加速计 - 板上安装 DBUS2 SENSOR INTERFACE RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| MCZ33784EF/R2- | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:DSI 2.02 Sensor Interface |
| MCZ33784EFR2 | 功能描述:加速计 - 板上安装 DBUS2 SENSOR INTERFACE RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| MCZ33789AE | 功能描述:网络控制器与处理器 IC Airbag ASSP RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。