参数资料
型号: MCZ33905S5EK
厂商: Freescale Semiconductor
文件页数: 92/106页
文件大小: 0K
描述: IC SYSTEM BASIS CHIP GEN2 32SOIC
标准包装: 42
应用: 系统基础芯片
接口: CAN,LIN
电源电压: 5.5 V ~ 27 V
封装/外壳: 32-BSOP(0.295",7.50mm 宽)裸露焊盘
供应商设备封装: 32-SOICW 裸露焊盘
包装: 管件
安装类型: 表面贴装
Analog Integrated Circuit Device Data
86
Freescale Semiconductor
33903/4/5
SERIAL PERIPHERAL INTERFACE
FLAGS AND DEVICE STATUS
CAN
CAN driver
state
Description
Report real time CAN bus driver state: 1 if Driver is enable, 0 if driver disable
Set / Reset condition
Set: CAN driver is enable. Reset: CAN driver is disable. Driver can be disable by SPI command (ex
CAN set in RXD only mode) or following a failure event (ex: TXD Dominant). Flag read SPI command
(0x2180) do not clear the flag, as it is “real time” information.
CAN receiver
state
Description
Report real time CAN bus receiver state: 1 if Enable, 0 if disable
Set / Reset condition
Set: CAN bus receiver is enable. Reset: CAN bus receiver is disable. Receiver disable by SPI
command (ex: CAN set in sleep mode). Flag read SPI command (0x2180) do not clear the flag, as it
is “real time” information.
CAN WU
enable
Description
Report real time CAN bus Wake-up receiver state: 1 if WU receiver is enable, 0 if disable
Set / Reset condition
Set: CAN Wake-up receiver is enable. Reset: CAN Wake-up receiver is disable. Wake-up receiver is
controlled by SPI, and is active by default after device Power ON. SPI command (0x2180) do not
change flag state.
CAN
Wake-up
Description
Report that Wake-up source is CAN
Set / Reset condition
Set: after CAN wake detected. Reset: Flag read (SPI)
CAN
Overtemp
Description
Report that the CAN interface has reach overtemperature threshold.
Set / Reset condition
Set: CAN thermal sensor above threshold. Reset: thermal sensor below threshold and flag read (SPI)
Description
Report that RXD pin is shorted to GND.
Set / Reset condition
Set: RXD low failure detected. Reset: failure recovered and flag read (SPI)
Rxd high
Description
Report that RXD pin is shorted to recessive voltage.
Set / Reset condition
Set: RXD high failure detected. Reset: failure recovered and flag read (SPI)
TXD dom
Description
Report that TXD pin is shorted to GND.
Set / Reset condition
Set: TXD low failure detected. Reset: failure recovered and flag read (SPI)
Bus Dom
clamp
Description
Report that the CAN bus is dominant for a time longer than tDOM
Set / Reset condition
Set: Bus dominant clamp failure detected. Reset: failure recovered and flag read (SPI)
CAN
Overcurrent
Description
Report that the CAN current is above CAN overcurrent threshold.
Set / Reset condition
Set: CAN current above threshold. Reset: current below threshold and flag read (SPI)
CAN_UF
Description
Report that the CAN failure detection has not yet identified the bus failure
Set / Reset condition
Set: bus failure pre detection. Reset: CAN bus failure recovered and flag read
CAN_F
Description
Report that the CAN failure detection has identified the bus failure
Set / Reset condition
Set: bus failure complete detetction.Reset: CAN bus failure recovered and flag read
CANL
to VBAT
Description
Report CAN L short to VBAT failure
Set / Reset condition
Set: failure detected. Reset failure recovered and flag read (SPI)
CANL to VDD
Description
Report CANL short to VDD
Set / Reset condition
Set: failure detected. Reset failure recovered and flag read (SPI)
CANL to GND Description
Report CAN L short to GND failure
Set / Reset condition
Set: failure detected. Reset failure recovered and flag read (SPI)
CANH
to VBAT
Description
Report CAN H short to VBAT failure
Set / Reset condition
Set: failure detected. Reset failure recovered and flag read (SPI)
CANH to VDD
Description
Report CANH short to VDD
Set / Reset condition
Set: failure detected. Reset failure recovered and flag read (SPI)
CANH to
GND
Description
Report CAN H short to GND failure
Set / Reset condition
Set: failure detected. Reset failure recovered and flag read (SPI)
Notes
50.
Not available on “C” versions
Table 40. Flag Descriptions
Flag
Description
相关PDF资料
PDF描述
V150C36H150BL2 CONVERTER MOD DC/DC 36V 150W
C8051F985-GM IC MCU 8BIT 2KB FLASH 20QFN
901-9610-3SF CONN SMA BULKHEAD JACK CRIMP
V150C36H150BF3 CONVERTER MOD DC/DC 36V 150W
V24A28E500BF3 CONVERTER MOD DC/DC 28V 500W
相关代理商/技术参数
参数描述
MCZ33905S5EK/R2 制造商:Freescale Semiconductor 功能描述:IC SBC GEN2 CAN LIN X1 32SOIC 制造商:Freescale Semiconductor 功能描述:IC, SBC, GEN2, CAN, LIN X1, 32SOIC
MCZ33905S5EKR2 功能描述:CAN 接口集成电路 5V SBC HSCAN SNGL LIN RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube
MCZ33905S5R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:SBC Gen2 with CAN High Speed and LIN Interface
MCZ33927EK 功能描述:功率驱动器IC THREE PHASE PRE- DRIVER RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MCZ33927EK/R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Three-Phase Field Effect Transistor Pre-Driver