- 您现在的位置：买卖IC网 > PDF目录98046 > MTD3302 (ON SEMICONDUCTOR) 8300 mA, 30 V, N-CHANNEL, Si, SMALL SIGNAL, MOSFET PDF资料下载
参数资料
| 型号： | MTD3302 |
| 厂商： | ON SEMICONDUCTOR |
| 元件分类： | 小信号晶体管 |
| 英文描述： | 8300 mA, 30 V, N-CHANNEL, Si, SMALL SIGNAL, MOSFET |
| 封装： | DPAK-3 |
| 文件页数： | 2/12页 |
| 文件大小： | 278K |
| 代理商： | MTD3302 |
MTD3302
http://onsemi.com
10
Another alternative would be to use a ceramic substrate
or an aluminum core board such as Thermal Clad
t. Using
a board material such as Thermal Clad, an aluminum core
board, the power dissipation can be doubled using the same
footprint.
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads.
Solder stencils are used to screen the optimum amount.
These stencils are typically 0.008 inches thick and may be
made of brass or stainless steel. For packages such as the
SC59, SC70/SOT323, SOD123, SOT23, SOT143,
SOT223, SO8, SO14, SO16, and SMB/SMC diode
packages, the stencil opening should be the same as the pad
size or a 1:1 registration. This is not the case with the DPAK
and D2PAK packages. If one uses a 1:1 opening to screen
solder onto the drain pad, misalignment and/or
“tombstoning” may occur due to an excess of solder. For
these two packages, the opening in the stencil for the paste
should be approximately 50% of the tab area. The opening
for the leads is still a 1:1 registration. Figure 16 shows a
typical stencil for the DPAK and D2PAK packages. The
pattern of the opening in the stencil for the drain pad is not
critical as long as it allows approximately 50% of the pad to
be covered with paste.
Figure 19. Typical Stencil for DPAK and
D2PAK Packages
SOLDER PASTE
OPENINGS
STENCIL
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within
a short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100
°C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering
method, the difference shall be a maximum of 10
°C.
The soldering temperature and time shall not exceed
260
°C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient shall be 5
°C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and
result in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied
during cooling.
* Soldering a device without preheating can cause
excessive thermal shock and stress which can result in
damage to the device.
* Due to shadowing and the inability to set the wave height
to incorporate other surface mount components, the D2PAK
is not recommended for wave soldering.
相关PDF资料 |
PDF描述 |
|---|---|
| MTD4N20E | 4 A, 200 V, 1.2 ohm, N-CHANNEL, Si, POWER, MOSFET |
| MTD4N20E1 | 4 A, 200 V, 1.2 ohm, N-CHANNEL, Si, POWER, MOSFET |
| MTD4N20E-1 | 4 A, 200 V, 1.2 ohm, N-CHANNEL, Si, POWER, MOSFET |
| MTD9N10ET4 | 9 A, 100 V, 0.25 ohm, N-CHANNEL, Si, POWER, MOSFET |
| MTD9N10E | 9 A, 100 V, 0.25 ohm, N-CHANNEL, Si, POWER, MOSFET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MTD3302T4 | 制造商:ON Semiconductor 功能描述:Trans MOSFET N-CH 30V 30A 3-Pin(2+Tab) DPAK T/R 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:ON Semiconductor 功能描述:MOSFET Transistor, N-Channel, TO-252AA |
| MTD3610D3 | 功能描述:Photodiode 940nm 制造商:marktech optoelectronics 系列:- 包装:散装 零件状态:有效 波长:940nm 颜色 - 增强:- 频谱范围:400nm ~ 1060nm 二极管类型:- 不同 nm 时的响应度:0.45 A/W @ 660nm 响应时间:- 电压 - DC 反向（Vr）（最大值）:20V 电流 - 暗（典型值）:10nA 有效面积:- 视角:- 工作温度:-20°C ~ 85°C 安装类型:- 封装/外壳:- 标准包装:10 |
| MTD392 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Coaxial Transceiver Interface |
| MTD392N | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Coaxial Transceiver Interface |
| MTD392V | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Coaxial Transceiver Interface |
发布紧急采购，3分钟左右您将得到回复。