- 您现在的位置：买卖IC网 > PDF目录1956 > NCN6004AFTBR2G (ON Semiconductor)IC INTERFACE SAM/SIM DUAL 48TQFP PDF资料下载
参数资料
| 型号： | NCN6004AFTBR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 8/40页 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE SAM/SIM DUAL 48TQFP |
| 标准包装： | 1 |
| 应用： | PC，PDA |
| 接口： | 微控制器 |
| 电源电压： | 1.8 V ~ 5.5 V |
| 封装/外壳： | 48-TQFP 裸露焊盘 |
| 供应商设备封装： | 48-TQFP（7x7） |
| 包装： | 标准包装 |
| 安装类型： | 表面贴装 |
| 其它名称： | NCN6004AFTBR2GOSDKR |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
NCN6004A
http://onsemi.com
16
Table 3. Status Pins Data
STATE
(HEX)
PGM
A3
A2
A1
A0
CARD_SEL
STATUS #A
STATUS #B
00
1
X
0
X
Vcc_Vbat_OK Pass = Low
VCC_OK Fail = High
01
1
X
0
1
CRD_VCC_A In Range
Pass = High Fail =Low
02
1
X
1
0
1
CRD_VCCA Overloaded
Pass = High Fail = Low
03
1
X
1
CRD_DET_A
Card Present = High
00
1
X
0
X
VCC_OK Pass = Low
VCC_OK Fail = High
01
1
X
0
1
0
CRD_VCC_B In Range
Pass = High Fail =Low
02
1
X
1
0
CRD_VCC_B Overloaded
Pass = High Fail = Low
03
1
X
1
0
CRD_DET_A
Card Present = High
*The STATUS register is not affected when the NCN6004A operates in any of the programming mode.
Vbat
2.10 V
2.00 V
2.70 V
3.30 V
Vbat_OK
Vbat STATUS
Max. ANLG_VCC Under Voltage
Min. ANLG_VCC Under Voltage
Typical ANLG_VCC Operating Voltage
The input power supply voltage monitoring applies to the card selected.
Figure 5. Reading ANLG_VCC Status (monitoring ANLG_VCC input voltage)
SYSTEM STATES UPON UPON STARTUP
Table 4. Operating Conditions Upon Startup
CRD_VCC_A
3.0 V
CRD_VCC_B
3.0 V
CRD_CLK_A
1/1 Ratio
CRD_CLK_B
1/1 Ratio
CRD_CLK_A
START (clock is valid)
CRD_CLK_B
START (clock is valid)
CRD_CLK_A
Low Speed Slope
CRD_CLK_B
Low Speed Slope
CLOCK Route
Direct (CLK_A
→ A, CLK_B → B)
Depending upon the logic state at turn on present on
pin 44, the system will run into a parallel mode
(MUX_MODE = L)
or
a
multiplexed
mode
(MUX_MODE = H). It is not possible to change the logic
state once the system is running.
Similarly, depending upon the logic state present pin 45,
the internal pull up resistors (I/O_A and I/O_B line) will be
either connected to ANLG_VCC voltage (EN_RPU = H) or
disconnected (EN_RPU = L). It is not possible to change this
operating condition once the system is running.
相关PDF资料 |
PDF描述 |
|---|---|
| NCN6804MNR2G | IC SMART CARD DUAL W/SPI 32-QFN |
| NCN7200MTTWG | IC MUX/DEMUX OCTAL 1X2 42WQFN |
| NCN8024DTBR2G | SMART CARD IC 5V/3V TSSOP |
| NCN8024RDWR2G | IC SMART CARD IC2 28SOIC |
| NCN8025MTTBG | IC SMART CARD I2C 16-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCN6010 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010/D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010_06 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010DTB | 功能描述:转换 - 电压电平 2.7V Sim Card RoHS:否 制造商:Micrel 类型:CML/LVDS/LVPECL to LVCMOS/LVTTL 传播延迟时间:1.9 ns 电源电流:14 mA 电源电压-最大:3.6 V 电源电压-最小:3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MLF-8 |
发布紧急采购，3分钟左右您将得到回复。