- 您现在的位置：买卖IC网 > Datasheet目录345 > NCP1910GEVB (ON Semiconductor)BOARD DEMO NCP1910DEMO-B-TLS Datasheet资料下载
参数资料
| 型号： | NCP1910GEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 31/37页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO NCP1910DEMO-B-TLS |
| 设计资源： | NCP1910 Schematic NCP1910GEVB BOM |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 最低可调至 0.8V |
| 电流 - 输出： | 3A |
| 输入电压： | 3 ~ 5.5 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 1MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | NCP1910 |
| 其它名称： | NCP1910GEVBOS |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页
NCP1910
490 10 6 V Rt
R min +
490 10 6 V Rt
R max +
? The minimum switching frequency is given by the R min
resistor value. This frequency is reached if there is no
feedback action and soft start period has already
elapsed.
(eq. 22)
F min
? The maximum switching frequency excursion is limited
by the R max selection. Note that the maximum
frequency is influenced by the opto ? coupler saturation
voltage value.
(eq. 23)
F max * F min
The definition of start ? up, shut ? off and these 2 delay
timers (t DEL1 and t DEL2 ) will be depicted later in “combo
management section”.
There are the other 2 delay timers are built ? in after the
brown ? out comparator:
? t BOK is the delay timer after V bulk is rising above the
BO level.
? t BONOTOK is the delay timer after V bulk is falling down
the BO level.
NCP1910 gets the information of V bulk from the PFC FB
pin, which minimizes the losses of the high voltage sensing
circuit. As depicted in Figure 22, 3 resistors (R 1 , R 2 , and R 3 )
among V REF , PG adj , BO adj pin, and ground determine the
levels of PG out signal and LLC brown ? out as the following
formulas:
R SS +
V PG + @ V REF
+ V bulk,PG @
? Resistor R SS together with capacitor C SS prepares the
soft start period for the resonant converter.
490 10 6 V Rt
(eq. 24)
F SS * F min
Where:
R 2 ) R 3
R 1 ) R 2 ) R 3
R FBL
R FBU ) R FBL
+ V bulk,PG @
(eq. 25)
V PREF
V bulk,nom
V BO + @ V REF
+ V bulk,BO @ + V bulk,BO @
V bulk,PG
R 2
? V Rt = 3.5 V
? F min is the minimal frequency
? F max is the maximal frequency
? F SS is the maximal soft start switching frequency
LLC Power Good Signal and Brown ? out (PG adj , PG out
and BO adj Pin)
As shown in Figure 22, the NCP1910 provides the
Brown ? Out circuitry (BO) that offer a way to protect the
resonant converter from operating at too low V bulk . In the
mean time, NCP1910 provides a Power Good signal (PG out )
to inform the isolated secondary side that the NCP1910 is in
order of match.
Once the PFC has started and raises V bulk above 95% of
its regulated voltage, an internal “PFC_OK” signal is
asserted. 20 ms later (t DEL1 ), the PG out pin is brought low.
The PG out signal can now disappear, which will release
PG out pin open, in two cases:
? V bulk decreases to the level, programmed by a reference
voltage imposed on PG adj pin. This level is usually
above the LLC turn ? off voltage, programmed by BO adj
pin. Therefore, in a normal turn ? off sequence, PG first
drops and informs the secondary side that it must be
prepared for shutdown.
? The second event that can drop the PG signal is when
the PFC experiences a fault: broken feedback path
(PFC UVP), PFC abnormal, or input line brown ? out. In
either case, the internal PFCok signal will drop and
then assert the PG out signal high, and starts a 5 ms timer
(t DEL2 ). Once this timer is elapsed, the LLC converter
can be safely halted.
R 3
R 1 ) R 2 ) R 3
(eq. 26)
R FBL V PREF
R FBU ) R FBL V bulk,nom
Where:
? V PG is the voltage on PG adj pin
? V BO is the voltage on BO adj pin
? V REF is the reference voltage (5 V typically).
? V PREF is the internal reference voltage for PFC
feedback OTA (2.5 V typically)
? V bulk,PG is the bulk voltage when PG out pin is
released open.
? V bulk,BO is the bulk voltage when brown ? out
function of LLC activates.
? V bulk,nom is the normal bulk voltage, e.g. 390 V.
Divide Equation 25 by 26, we can get the relationship
between R 2 and R 3 in Equation 27:
+ * 1 (eq. 27)
R 3 V bulk,BO
Hence, by given V bulk,PG and V bulk,BO , and choose the
value R 3 as the 1 st step, we can get the R 2 by Equation 27 and
R 1 by Equation 26.
For example, V bulk,nom is 390 V, V bulk,PG is 340 V, and
V bulk,BO is 330 V. Choose 10 k W resistor as R 3 . Then R2 is
303 W . Choose 300 W as it is the closet standard resistor.
Then we can get the R 1 is 13.3 k W .
http://onsemi.com
31
相关PDF资料 |
PDF描述 |
|---|---|
| NCP3418BMNR2G | IC MOSFET DRIVER DUAL 12V 10-DFN |
| NCP3418DR2 | IC MOSFET DRIVER DUAL 12V 8-SOIC |
| NCP3420DR2G | IC MOSFET DRIVER DUAL 12V 8-SOIC |
| NCP3488DR2G | IC MOSFET DRVR DUAL 12V 8-SOIC |
| NCP5007SNT1 | IC LED DRIVR WHT COMPACT 5TSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1927DR2G | 功能描述:功率因数校正 IC PFC AND FLYBACK CONTROLER RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| NCP1937A1DR2G | 制造商:ON Semiconductor 功能描述:COMBO PFC & QUAZI FLYBACK - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / COMBO PFC & QUAZI FLYBACK |
| NCP1937B1DR2G | 制造商:ON Semiconductor 功能描述:COMBO PFC & QUAZI FLYBACK - Tape and Reel |
| NCP1937BADAPGEVB | 制造商:ON Semiconductor 功能描述:ADPTR 90W PFC+QR<10MW - Bulk 制造商:ON Semiconductor 功能描述:BOARD EVAL FOR NCP1937 制造商:ON Semiconductor 功能描述:Power Management IC Development Tools 90 W Adapter PFC+QR 10 MW Eval Brd |
| NCP21WB333 | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:for Surface Mounting Application |
发布紧急采购，3分钟左右您将得到回复。