参数资料
型号: PH28F128L18T85
厂商: INTEL CORP
元件分类: PROM
英文描述: StrataFlash Wireless Memory
中文描述: 8M X 16 FLASH 1.8V PROM, 85 ns, PBGA56
封装: 0.75 MM PITCH, LEAD FREE, VFBGA-56
文件页数: 67/106页
文件大小: 1272K
代理商: PH28F128L18T85
Intel StrataFlash Wireless Memory (L18)
Datasheet
Intel StrataFlash Wireless Memory (L18)
Order Number: 251902, Revision: 009
April 2005
67
13.1.4
Block Lock Status
The Read Device Identifier command is used to determine a block’s lock status (see
Section 15.2,
“Read Device Identifier” on page 76
). Data bits DQ[1:0] display the addressed block’s lock status;
DQ0 is the addressed block’s lock bit, while DQ1 is the addressed block’s lock-down bit.
Block Locking State Diagram
13.1.5
Block Locking During Suspend
Block lock and unlock changes can be performed during an erase suspend. To change block
locking during an erase operation, first issue the Erase Suspend command. Monitor the Status
Register until SR[7] and SR[6] are set, indicating the device is suspended and ready to accept
another command.
Next, write the desired lock command sequence to a block, which changes the lock state of that
block. After completing block lock or unlock operations, resume the erase operation using the
Erase Resume command.
Note:
A Lock Block Setup command followed by any command other than Lock Block, Unlock Block,
or Lock-Down Block produces a command sequence error and set Status Register bits SR[4] and
SR[5]. If a command sequence error occurs during an erase suspend, SR[4] and SR[5] remains set,
even after the erase operation is resumed. Unless the Status Register is cleared using the Clear
Status Register command before resuming the erase operation, possible erase errors may be
masked by the command sequence error.
Figure 28.
[X00]
[X01]
Power-Up/Reset
Unlocked
Locked
[011]
[111]
[110]
Locked-
Down
Software
Locked
[011]
Hardware
Locked
Unlocked
WP# Hardware Control
Notes:
1. [a,b,c] represents [WP#, DQ1, DQ0]. X = Don’t Care.
2. DQ1 indicates Block Lock-Down status. DQ1 = ‘0’, Lock-Down has not been issued
to this block. DQ1 = ‘1’, Lock-Down has been issued to this block.
3. DQ0 indicates block lock status. DQ0 = ‘0’, block is unlocked. DQ0 = ‘1’, block is
locked.
4. Locked-down = Hardware + Software locked.
5. [011] states should be tracked by system software to determine difference between
Hardware Locked and Locked-Down states.
Software Block Lock (0x60/0x01) or Software Block Unlock (0x60/0xD0)
Software Block Lock-Down (0x60/0x2F)
WP# hardware control
相关PDF资料
PDF描述
PH28F256L18B85 StrataFlash Wireless Memory
PH28F256L18T85 StrataFlash Wireless Memory
PH28F640L18B85 StrataFlash Wireless Memory
PH28F640L18T85 StrataFlash Wireless Memory
PH2907A PNP switching transistor
相关代理商/技术参数
参数描述
PH28F128W18BD60A 制造商:Micron Technology Inc 功能描述:NOR Flash Parallel 1.8V 128Mbit 8M x 16bit 60ns 56-Pin VFBGA Tray
PH28F160C3BD70A 制造商:Micron Technology Inc 功能描述:MM#865392FLASH 28F160C3BD 70 VF-PBGA46 C
PH28F256L18B85 制造商:INTEL 制造商全称:Intel Corporation 功能描述:StrataFlash Wireless Memory
PH28F256L18B85A 制造商:Micron Technology Inc 功能描述:MM#875138FLASH 28F256L18B 85 VF-PBGA79 S
PH28F256L18T85 制造商:INTEL 制造商全称:Intel Corporation 功能描述:StrataFlash Wireless Memory